Bissoy.com
Doctors Medicines MCQs Q&A

When steam is used on the tube side of the Heat Exchanger, then the allowable pressure drop should be less than _____ P.S.I.

When steam is used on the tube side of the Heat Exchanger, then the allowable pressure drop should be less than _____ P.S.I. Correct Answer 1

If we keep a very high pressure drop for the steam then there would be unnecessary condensation of the steam decreasing the Heat transfer coefficient.

Related Questions

In a counter flow heat exchanger, water flowing through a tube of 10 cm inner diameter is heated by steam condensing on the outside of the tube. The convective film coefficient on the water and steam side are estimated to be 12000 and 20000 k J/m2 hr degree. Neglecting tube thickness and its resistance to heat flow, workout the overall heat transfer coefficient for the heat exchanger
Plate type heat exchangers have less surface area as compared to a similar Shell and Tube heat exchanger. A Shell and Tube Heat Exchanger of equivalent area weigh six-seven times less than a Plate Type heat exchanger.
A single pass shell and tube heat exchanger, consisting of a bundle of 100 tubes (inner diameter 25 mm and thickness 2 mm) is used for heating 28 kg/s of water from 25 degree Celsius to 75 degree Celsius with the help of a steam condensing at atmospheric pressure on the shell side with condensing heat transfer coefficient 5000 W/m2 degree. Make calculation for overall heat transfer coefficient based on the inner area. Take fouling factor on the water side to be 0.002 m2 degree/W per tube and neglect effect of fouling factor on the shell side and thermal resistance of the tube wall
Air is to be heated by condensing steam. Two heat exchangers are available (i) a shell and tube heat exchanger and (ii) a finned tube heat exchanger. Tube side heat transfer area are equal in both the cases. The recommended arrangement is
In a surface condenser, the water flowing through a series of tubes at the rate of 200 kg/hr is heated from 15 degree Celsius to 75 degree Celsius. The steam condenses on the outside surface of tubes at atmospheric pressure and the overall heat transfer coefficient is estimated at 860 k J/m2 hr degree. Find the effectiveness of the heat exchanger. At the condensing pressure, stream has a saturation temperature 0f 100 degree Celsius and the latent heat of vaporization is 2160 k J/kg. Further, the steam is initially just saturated and the condensate leaves the exchanger without sub-cooling i.e. only latent heat of condensing steam is transferred to the water. Take specific heat of water as 4 k J/kg K
In a surface condenser, the water flowing through a series of tubes at the rate of 200 kg/hr is heated from 15 degree Celsius to 75 degree Celsius. The steam condenses on the outside surface of tubes at atmospheric pressure and the overall heat transfer coefficient is estimated at 860 k J/m2 hr degree. Find the number of transfer units of the heat exchanger. At the condensing pressure, stream has saturation temperature 0f 100 degree Celsius and the latent heat of vaporization is 2160 k J/kg. Further, the steam is initially just saturated and the condensate leaves the exchanger without sub-cooling i.e. only latent heat of condensing steam is transferred to water. Take specific heat of water as 4 k J/kg K
A particle of mass m is confined in the potential
Quantum Mechanics mcq question image
\[V\left( x \right) = \left\{ {\begin{array}{*{20}{c}} {\frac{1}{2}m{\omega ^2}{x^2},}&{{\text{for }}x Let the wave function of the particle be given by $$\psi \left( x \right) = - \frac{1}{{\sqrt 5 }}{\psi _0} + \frac{2}{{\sqrt 5 }}{\psi _1}$$
where $${\psi _0}$$ and $${\psi _1}$$ are the eigen functions of the ground state and the first excited slate respectively. The expectation value of the energy is
Read the passage carefully and choose the best answer to each question out of the four alternatives and click the button corresponding to it. The first working steam­ powered vehicle was designed and most likely built by Ferdinand Verbies, a Flemish member of a Jesuit mission in China around 1672. It was a 65 cm long scale­ model toy for the Chinese Emperor, that was unable to carry a driver or a passenger. It is not known if Verbiest's model was ever built. Nicolas- Joseph Cugnot is widely credited with building the first full­ scale, self ­propelled mechanical vehicle or automobile in about 1769; he also created a steam­ powered tricycle. He constructed two steam tractors for the French Army, one of which is preserved in the French National Conservatory of Arts and Crafts. His inventions were however handicapped by problems of water supply and maintaining steam pressure. In 1801, Richard Trevithick built and demonstrated his Puffing Devil road locomotive, believed by many to be the first demonstration of a steam ­powered road vehicle. It was unable to maintain sufficient steam pressure for long periods. Sentiment against steam ­powered road vehicles led to the Locomotive Acts of 1865. In 1807 Nicephore Niepce and his brother Claude probably created the world's first internal combustion engine which they called Pyreolophore. The first full­scale, working steam ­powered tricycle was built by:
Read the passage carefully and choose the best answer to each question out of the four alternatives and click the button corresponding to it. The first working steam­ powered vehicle was designed and most likely built by Ferdinand Verbies, a Flemish member of a Jesuit mission in China around 1672. It was a 65 cm long scale­ model toy for the Chinese Emperor, that was unable to carry a driver or a passenger. It is not known if Verbiest's model was ever built. Nicolas- Joseph Cugnot is widely credited with building the first full­ scale, self ­propelled mechanical vehicle or automobile in about 1769; he also created a steam­ powered tricycle. He constructed two steam tractors for the French Army, one of which is preserved in the French National Conservatory of Arts and Crafts. His inventions were however handicapped by problems of water supply and maintaining steam pressure. In 1801, Richard Trevithick built and demonstrated his Puffing Devil road locomotive, believed by many to be the first demonstration of a steam ­powered road vehicle. It was unable to maintain sufficient steam pressure for long periods. Sentiment against steam ­powered road vehicles led to the Locomotive Acts of 1865. In 1807 Nicephore Niepce and his brother Claude probably created the world's first internal combustion engine which they called Pyreolophore. Cugnot built steam tractors for:
From the given table, what is the percentage of students scoring 40 or more, but less than 70. Scores Less than 20 Less than 30 Less than 40 Less than 50 Less than 60 Less than 70 Less than 80 No. of Students 12 19 22 31 38 46 50