Bissoy.com
Doctors Medicines MCQs Q&A

Plate type heat exchangers which are made of thin plates, can handle high pressure and temperature difference.

Plate type heat exchangers which are made of thin plates, can handle high pressure and temperature difference. Correct Answer False

The thin primed plates of this type of heat exchangers are not equipped to handle high pressure and temperature as this may cause leakage and other complications to the equipment.

Related Questions

A composite wall consists of two plates A and B placed in series normal to the flow of heat. The thermal conductivities are kA and kB and the specific heat capacities are CPA and CPB for plates A and B respectively. Plate B has twice the thickness of plate A. At steady state, the temperature difference across plate A is greater than that across plate B, when
A composite wall consists of two plates A and B placed in series normal to the flow of heat. The thermal conductivities are kA and kB and the specific heat capacities are CPA and CPB for plates A and B respectively. Plate B has twice the thickness of plate A. At steady state, the temperature difference across plate A is greater than that across plate B, when
Statement 1: Plate heat exchangers are used in heat sensitive foods like milk. Statement 2: Principle behind plate heat exchangers is that there is very less space between the plates and hence quick heating can take place.
To effect a bond between two metal plates, 2.5 cm and 15 cm thick, heat is uniformly applied through the thinner plate by a radiant heat source. The bonding must be held at 320 K for a short time. When the heat source is adjusted to have a steady value of 43.5 k W/m2, a thermocouple installed on the side of the thinner plate next to source indicates a temperature of 345 K. Calculate the temperature gradient for heat conduction through thinner plate. In the diagram, the upper plate is 2.5 cm thick while the lower is 15 cm thick.
Rinki has three plates of Jalebies: Plate A, Plate B and Plate C. Plate A has only one Jalebi, Plate B has five Jalebies and Plate C has three Jalebies. She wants to put equal numbers of Jalebies in all the plates. Which of the following statement is true?
The important design and operating considerations for Extended-Surface Compact Heat Exchangers are: (1) Both fluids may have high or low heat transfer coefficients (2) As the tubes are very narrow (low DH), the fluid used should not be corrosive as effective cleaning of tubes is not possible. (3) The fluid pressure drop calculation is important as a regulatory method to ensure long life of the tubes. (4) Unlike shell and tube type heat exchangers, these are limited when it comes to operating pressure and temperature.
A parallel-plate capacitor of capacitance C1 is made using two gold plates. Another parallel-plate capacitor of capacitance C2 is made using two aluminium plates with same plate separation, and all the four plates are of same area. If ρg and ρa are respectively the electrical resistivity of gold and aluminium, then which one of the following relations is correct?
A parallel-plate capacitor of capacitance C1is made using two gold plates. Another parallel-plate capacitor of capacitance C2is made using two aluminium plates with same plate separation, and all the four plates are of same area. If gand aPare respectively the electrical resistivities of gold and aluminium, then which one of the following relations is correct?
A parallel-plate capacitor of capacitance C1 is made using two gold plates. Another parallel-plate capacitor of capacitance C2 is made using two aluminium plates with same plate separation, and all the four plates are of same area. If rg and ra are respectively the electrical resistivities of gold and aluminium, then which one of the following relations is correct?
The handle of a saucepan, 30 cm long and 2 cm in diameter, is subjected to 100 degree Celsius temperature during a certain cooking operation. The average unit surface conductance over the handle surface is 7.35 W/m2 degree in the kitchen air at 24 degree Celsius. The cook is likely to grasp the last 10 cm of the handle and hence the temperature in this region should not exceed 38 degree Celsius. What should be the thermal conductivity of the handle material to accomplish it? The handle may be treated as a fin insulated at the tip