Bissoy.com
Doctors Medicines MCQs Q&A

What is the heat transferred from the system if the output sensible heat is 5 J, input sensible heat is 25 J, and heat of solution is 20 J?

What is the heat transferred from the system if the output sensible heat is 5 J, input sensible heat is 25 J, and heat of solution is 20 J? Correct Answer 0

Q = ∆Hout,sensible – ∆Hin,sensible + ∆Hsolution = 5 – 15 + 20 = 15 J.

Related Questions

What is the heat transferred from the system if the output sensible heat is 10 J, input sensible heat is 15 J, and heat of solution is 20 J?
What is the heat transferred from the system if the output sensible heat is 5 J, input sensible heat is 20 J, and heat of solution is 10 J?
What is the heat transferred from 5 mole of the system if the output sensible heat is 1 J/mole, input sensible heat is 3 J/mole, and heat of solution is 4 J/mole?
What is the heat transferred from 2 mole of the system if the output sensible heat is 3 J/mole, input sensible heat is 2 J/mole, and heat of solution is 2 J/mole?
Which of the following statements is/are correct? 1. A system is said to be Finite Impulse Response (FIR), if the output samples of the system depend only on the present input and a finite number of past or previous input samples. 2. If the output of a system y(n) depends only on the present input and past inputs, but not on past outputs, then it is called a non-recursive system. 3. If the output of a system y(n) depends only on the present input and past inputs, but not on past outputs, then it is called a recursive system.
A 60% spirit solution is mixed with r% spirit solution in the ratio 1 : 3 such that a s% spirit solution is obtained. When a (s/3)% spirit solution is mixed with 55% spirit solution in equal ratio, an (r/2)% spirit solution is obtained. Which of the following can be determined? (A) Value of ‘r’ (B) Value of ‘s’ (C) Volume of the 60% spirit solution mixed initially (D) If 9 liters of r% spirit solution was mixed initially, what was the volume of the s% spirit solution thus obtained?
A system provides output yi(t) when xi(t) is applied. If the system is said to be LTI then which of the following properties must satisfy? (i).If the input is x3 = ax1(t) + bx2(t), then output must be y3(t) = ay1(t) + by2(t) (ii).If the input is x(t – T), then the output must be y (t – T) (iii).If the input is x3 = ax1(t) + bx2(t), then output must be y3(t) = ay1(t) * by2(t) (iv).If the input is x(t – T), then the output must be y(t + T)
Consider a system whose input r and output y are related by the equation $$y\left( t \right) = \int\limits_{ - \infty }^\infty {x\left( {t - \tau } \right)} h\left( {2\tau } \right)d\tau $$
Signal Processing mcq question image
Where h(t) is shown in the graph
Which of the following four properties are possessed by the system? BIBO: Bounded input gives a bounded output
Causal: The system is causal.
LP : The system is low pass.
LTI: The system is linear and time-invariant.
A chemical solution appears green when the salt concentration is 8 grams per litre (gpl) and red when it is 10 gpl. Pure water was added to the solution of 1 litre of 15 gpl solution till it turned green. Then 125 ml of the green solution is taken out and x grams of salt is added to the green solution to make it red. Another 500 ml of the final solution was taken out and y litres of green solution is added to get a resultant solution of concentration 9.6 gpl.  Assume adding salt doesn’t change its volume and find the ratio of x and y. 
In the question one statement is given, followed by two conclusions, I and II. You have to consider the statement to be true even if it seems to be at variance from commonly known facts. You have to decide which of the given conclusions, if any, follows from the given statement. Statement: A function is a relation between a set of input elements and a set of possible output elements where each input is related to exactly one output. Conclusion I: Every input element is related to every output element. Conclusion II: Every input element is related to one element of the output.