Bissoy.com
Doctors Medicines MCQs Q&A

Related Questions

Let D be a simple graph on 10 vertices such that there is a vertex of degree 1, a vertex of degree 2, a vertex of degree 3, a vertex of degree 4, a vertex of degree 5, a vertex of degree 6, a vertex of degree 7, a vertex of degree 8 and a vertex of degree 9. What can be the degree of the last vertex?
Let us say temperature of a body in degree Celsius and degree Rankine are related as TC = 50 + 3TR, what is the change in temperature in Kelvin, if the change in temperature in degree Rankine is 100oR?
Study the following statements.i) The displacement method is more useful when degree of kinematic indeterminacy is greater than the degree of static indeterminacy.ii) The displacement method is more useful when degree of kinematic indeterminacy is less than the degree of static indeterminacy.iii) The force method is more useful when degree of static indeterminacy is greater than the degree of kinematic indeterminacy.iv) The force method is more useful when degree of static indeterminacy is less than the degree of kinematic indeterminacy.The correct answer is
The rear window of an automobile is made of thick glass i.e. AB = 5 mm and thermal conductivity is 0.8 W/m degree. To defrost this window, a thin transparent film type heating element has been fixed to its inner surface. For the conditions given below, determine the electric power that must be provided per unit area of window if a temperature 5 degree Celsius is maintained at its outer surface. Interior air temperature and the corresponding surface coefficient are 20 degree Celsius and 12 W/m2 degree. Surrounding air temperature and the corresponding surface coefficient are – 15 degree Celsius and 70 W/m2 degree. Electric heater provides uniform heat flux
Which of the following statements are correct regarding the Rankine cycle? For a given set of operating pressure limits of a Rankine cycle, superheating the steam beyond the saturation temperature at the boiler pressure will result in: a. an increase in the moisture content of steam leaving the turbine b. an increase in thermal efficiency of the Rankine cycle c. an increase in the mean temperature of heat addition d. a decrease in the amount of heat rejected in the condenser
A water line is buried underground in dry soil that has an assumed initial temperature of 4.5 degree Celsius. The pipe may have no flow through it for long period of time, yet it will not be drained in order that no freezing occurs, the pipe must be kept at a temperature not lower than 0 degree Celsius. The pipe is to be designed for a 30 hour period at the beginning of which the soil surface temperature suddenly drops to – 17 degree Celsius. Workout the minimum earth covering needed above the water pipe so as to prevent the possibility of freezing during 36 hour cold spell. The soil in which the pipe is buried has the following properties Density = 640 kg/m3 Specific heat = 1843J/kg degree Thermal conductivity = 0.345 W/m degree
নিম্নের কত J তাপ বর্জন করা 100oC তাপমাত্রার 1 kg জলীয় বাষ্প 100oC তাপমাত্রার পানিতে পরিণত হয়?
150 J is the latent heat for vaporization of water, what is the heat of transition from 50oC water to 100oC steam if heat of transition from 50oC water to 100oC water is 12 J?
A 25 mm diameter egg roll (k = 1 W/m degree) is roasted with the help of microwave heating. For good quality roasting, it is desired that temperature at the center of roll is maintained at 100 degree Celsius when the surrounding temperature is 25 degree Celsius. What should be the heating capacity in W/m 3 of the microwave if the heat transfer coefficient on the surface of egg roll is 20 W/m2 degree?
The handle of a saucepan, 30 cm long and 2 cm in diameter, is subjected to 100 degree Celsius temperature during a certain cooking operation. The average unit surface conductance over the handle surface is 7.35 W/m2 degree in the kitchen air at 24 degree Celsius. The cook is likely to grasp the last 10 cm of the handle and hence the temperature in this region should not exceed 38 degree Celsius. What should be the thermal conductivity of the handle material to accomplish it? The handle may be treated as a fin insulated at the tip