Bissoy.com
Doctors Medicines MCQs Q&A

Related Questions

The rear window of an automobile is made of thick glass i.e. AB = 5 mm and thermal conductivity is 0.8 W/m degree. To defrost this window, a thin transparent film type heating element has been fixed to its inner surface. For the conditions given below, determine the electric power that must be provided per unit area of window if a temperature 5 degree Celsius is maintained at its outer surface. Interior air temperature and the corresponding surface coefficient are 20 degree Celsius and 12 W/m2 degree. Surrounding air temperature and the corresponding surface coefficient are – 15 degree Celsius and 70 W/m2 degree. Electric heater provides uniform heat flux
Let us say temperature of a body in degree Celsius and degree Rankine are related as TC = 50 + 3TR, what is the change in temperature in Kelvin, if the change in temperature in degree Rankine is 100oR?
A 2 cm thick steel slab heated to 525 degree Celsius is held in air stream having a mean temperature of 25 degree Celsius. Estimate the time interval when the slab temperature would not depart from the mean value of 25 degree Celsius by more than 0.5 degree Celsius at any point in the slab. The steel plate has the following thermal physical properties Density = 7950 kg/m3 C P = 455 J/kg K K = 46 W/m K
A water line is buried underground in dry soil that has an assumed initial temperature of 4.5 degree Celsius. The pipe may have no flow through it for long period of time, yet it will not be drained in order that no freezing occurs, the pipe must be kept at a temperature not lower than 0 degree Celsius. The pipe is to be designed for a 30 hour period at the beginning of which the soil surface temperature suddenly drops to – 17 degree Celsius. Workout the minimum earth covering needed above the water pipe so as to prevent the possibility of freezing during 36 hour cold spell. The soil in which the pipe is buried has the following properties Density = 640 kg/m3 Specific heat = 1843J/kg degree Thermal conductivity = 0.345 W/m degree
A counter flow heat exchanger is used to col 2000 kg/hr of oil (c p = 2.5 k J/kg K) from 105 degree Celsius to 30 degree Celsius by the use of water entering at 15 degree Celsius. If the overall heat transfer coefficient is expected to be 1.5 k W/m2 K, find out the water flow rate. Presume that the exit temperature of the water is not to exceed 80 degree Celsius
Two rods A and B of the same length and diameter protrude from a surface at 120 degree Celsius and are exposed at air at 25 degree Celsius. The temperatures measured at the end of the rods are 50 degree Celsius and 75 degree Celsius. If thermal conductivity of material A is 20W/ m K, calculate it for B
A body cooling from 80 degree Celsius to 70 degree Celsius takes 10 minutes when left exposed to environmental conditions. If the body is to cool further from 70 degree Celsius to 60 degree Celsius under the same external conditions, it will take
In a food processing plant, a brine solution is heated from – 12 degree Celsius to – 65 degree Celsius in a double pipe parallel flow heat exchanger by water entering at 35 degree Celsius and leaving at 20.5 degree Celsius. Let the rate of flow is 9 kg/min. Estimate the area of heat exchanger for an overall heat transfer coefficient of 860 W/m2 K. For water c P = 4.186 * 10 3 J/kg K
The engine oil at 150 degree Celsius is cooled to 80 degree Celsius in a parallel flow heat exchanger by water entering at 25 degree Celsius and leaving at 60 degree Celsius. Estimate the exchanger effectiveness
The engine oil at 150 degree Celsius is cooled to 80 degree Celsius in a parallel flow heat exchanger by water entering at 25 degree Celsius and leaving at 60 degree Celsius. Estimate the number of transfer units