Bissoy.com
Doctors Medicines MCQs Q&A

Related Questions

Which of the following statements is/are correct about a shaper and planer? I) A shaper is intended for small jobs, while a planer is intended for large jobs. II) A shaper has higher machining accuracy compared to a planer. III) A shaper is relatively lighter, smaller and cheaper as compared to a planer.
Directions : In each of the following questions a statement is given, followed by two conclusions. Give answer :

Statement : The General Administration Department has issued a circular to all the employees informing them that henceforth the employees can avail their lunch break at any of the half-hour slots between 1.00 p.m. and 2.30 p.m.

Assumptions :
I. The employees may welcome the decision and avail lunch break at different time's slots.
II. There may not be any break in the work of the organization as the employees will have their lunch break at different time slots.
When they had a meeting seven company executives __ T, U, V, W, X, Y and Z ___ sit at a rectangular table .Three executives sit along one side of the table , and three sit along the other side, each directly opposite one of the other three. The seventh sits at the head of the table . There is no seat at the foot of the table . Ualways sits in one of te two seats farthest from the head of the table. Y and V always sit next to each other .V never sits next to Z . If Z does not sit at the head of the table, W sits there. If W sits directly opposite T, X must sit next to which of the following excutives?
Some small cubes of same height 7 cm but variable length and width are put inside a large cuboid of height 21 cm. Length and width of cuboid is 32 cm and 24 cm, respectively. Small cubes are put such that cubes at the bottom most layer is of similar base area; second layer contains all the cubes of similar base area and third layer have all the cubes of similar base area. Which of the following statement(s) given below is / are TRUE? A: If side of each small cubes at bottom most layer is 8 cm, then maximum number of small cubes that can be put at bottom most layer is 12. B: If maximum of 48 cubes can be put at second layer, then side of each cube at second layer is 6 cm. C: If side of each small cubes at third layer is 1.6 cm, then maximum number of small cubes that can be put at third layer is 300.
Given below are two quantities named 1 and 2. Based on the given information, you have to determine the relationship between the two quantities. You should use the given data and your knowledge of Mathematics to choose between the possible answers. Quantity 1: P and Q can do a work in 6 days and Q and R can do a work in 60/7 days and P and R can do a work in 20/3 days. If Q and R work for first 2 days and left the work. Find the total time taken by P to complete the remaining work. Quantity 2: A and B can do a work in 8/3 days, B and C can do the same work in 3 days and A and C can do the same work in 24/5 days. In what time C alone can complete the work?
One side of a triangle and a rectangle is the same. The third vertex of the triangle lies on the midpoint of the rectangle side opposite the common side. The rectangle sides are in the ratio 2 : 3 and the common side is the longer side of the rectangle.  What is the sin value of the angle between the common side and the equal side of the triangle?
Which of the following is not true about the clamping force and clamping of dial indicators?
Which of the following carries clamping bolt T-slots for fixing work piece?
Six arms negotiators -- M,O,P,R,S and T-- are to be seated at a round table to discuss disarmament. There are exactly six chairs around the table. Each negotiator sits facing the center of the table and is directly opposite a negotiators across the table.The seating arrangement is subject to the following restrictions : T cannot sit next to P;S cannot sit next to M;R must sit next to M. If T sits directly across the table from O, who must sit on the other side of P?
The maximum harbour depth below lowest low water is generally equal to
(i) loaded draft + 1.2 m when bottom is rock
(ii) loaded draft + 1.8 m when bottom is soft
(iii) loaded draft + 1.2 m when bottom is soft
(iv) loaded draft + 1.8 m when bottom is rock