Bissoy.com
Doctors Medicines MCQs Q&A

In salvaging of castings, cooling fluid used can be directly exposed to the hot castings to enhance heat transfer.

In salvaging of castings, cooling fluid used can be directly exposed to the hot castings to enhance heat transfer. Correct Answer False

A cooling medium like coolant air from the compressor or steam is commonly directed to the casting along one or more casting surfaces. This flow for cooling is considered as backside flow, where the cooling medium is not directly exposed to the high temperature of surfaces of the casting.

Related Questions

Consider the following statements for cooling towers: 1. Cooling tower is an artificial device used to cool the hot cooling water coming out of condenser more effectively. 2. The amount of water usually lost with induced draft cooling tower ranges from 5% to 6% by evaporation. 3. The amount of water usually lost with induced draft cooling tower ranges from 7% to 8% by drift losses. 4. The rate of evaporation of water and its cooling effect on the remaining water depends upon the relative humidity of air passing through the tower. Which of the above statements are correct?
Concentrated fermentation liquid containing 20% (w/w) gluconic acid from an evaporator has a flow rate of 2000 kg/h and a temperature 90 °C. It needs to be cooled to 6 °C in a heat exchanger with cooling water. The cooling water has a flow rate 2700 kg/h and an initial temperature 2 °C. If the cooling water leaves the heat exchanger at 50 °C, what is the rate of heat loss from gluconic acid solution to the surroundings? Assume the heat capacity of gluconic acid is 0.35 cal/g-°C-1.
In a surface condenser, the water flowing through a series of tubes at the rate of 200 kg/hr is heated from 15 degree Celsius to 75 degree Celsius. The steam condenses on the outside surface of tubes at atmospheric pressure and the overall heat transfer coefficient is estimated at 860 k J/m2 hr degree. Find the number of transfer units of the heat exchanger. At the condensing pressure, stream has saturation temperature 0f 100 degree Celsius and the latent heat of vaporization is 2160 k J/kg. Further, the steam is initially just saturated and the condensate leaves the exchanger without sub-cooling i.e. only latent heat of condensing steam is transferred to water. Take specific heat of water as 4 k J/kg K
A designer chooses the values of fluid flow rates and specific heats in such a manner that the heat capacities of the two fluids are equal. A hot fluid enters the counter flow heat exchanger at 100°C and leaves at 60°C. A cold fluid enters the heat exchanger at 40°C. The mean temperature difference between the two fluids is
Bernoulli's equation for fluid flow is derived following certain assumptions. Out of the assumptions listed below, which set of assumptions is used in derivation of Bernoulli's equation?
1. Fluid flow is frictionless & irrotational
2. Fluid flow is steady
3. Fluid flow is uniform & turbulent
4. Fluid is compressible
5. Fluid is incompressible
A flat wall of fire clay, 50 cm thick and initially at 25 degree Celsius, has one of its faces suddenly exposed to a hot gas at 950 degree Celsius. If the heat transfer coefficient on the hot side is 7.5 W/m2 K and the other face of the wall is insulated so that no heat passes out of that face, determine the time necessary to raise the center of the wall to 350 degree Celsius. For fire clay brick Thermal conductivity = 1.12 W/m K Thermal diffusivity = 5.16 * 10 -7 m2/s
A heat exchanger with heat transfer surface area A and overall heat transfer coefficient U handles two fluids of heat capacities Cmax and Cmin. The number of transfer units (NTU) used in the analysis of heat exchanger is specified as
A heat exchanger with heat transfer surface area A and overall heat transfer coefficient U handles two fluids of heat capacities Cmax and Cmin. The number of transfer units (NTU) used in the analysis of heat exchanger is specified as
Consider the following statements pertaining to heat transfer through fins (i) They must be arranged at right angles to the direction of flow of working fluid (ii) The temperature along the fin is variable and accordingly heat transfer rate varies along the fin elements (iii) Fins are equally effective irrespective whether they are on the hot side or cold side of the fluid (iv) Fins are made of materials that have thermal conductivity higher than that of wall Identify the correct statements
In salvaging of castings, the metallic powder coating can improve the heat transfer by_____