Bissoy.com
Doctors Medicines MCQs Q&A

The process of draining steam from the turbine, at certain points during its expansion and using this steam for heating the feed water in feed water heaters and then supplying it to the boiler is known as?

The process of draining steam from the turbine, at certain points during its expansion and using this steam for heating the feed water in feed water heaters and then supplying it to the boiler is known as? Correct Answer bleeding

The process of draining steam from the turbine, at certain points during its expansion and using this steam for heating the feed water in feed water heaters and then supplying it to the boiler is known as Bleeding.

Related Questions

The process of draining steam from the turbine, at certain points during its expansion and using this steam for heating the feed water in feed water heaters and then supplying it to the boiler is known as
Ratio of chemical A and B in boiler Y is 3 : 2 and Boiler X has ratio of chemical A to chemical B as 1 : 7, 16 litres of mixture is removed transferred from boiler X to boiler Y. What is the total capacity of boiler Y if capacity of boiler X is 144 litres and difference between chemical A and B in boiler Y after transfer is 25 litres? Assume that after transferring 16 litres from boiler X, boiler Y is running at full capacity
The process of draining steam from the turbine, at specific points during its expansion for heating the feed water is called _____
Read the following statements about feed water heaters I. Open or contact heaters are also called Deaerator. II. Open or contact heaters constructed to remove non-condensable gases from feed water.
Which of the following statement(s) is/are incorrect? (i) A turbine is called an impulse turbine if at the inlet of the turbine total energy is only kinetic energy (ii) A turbine is called a reaction turbine if at the inlet of the turbine the total energy is kinetic energy and pressure energy (iii) The inward flow reaction turbine having radial discharge at the outlet is known as Kaplan turbine
A steam turbine in which a part of the steam after the expansion is used for process heating and the remaining steam is further expanded for power generation is/are: 1.Impulse turbine 2.Pass out turbine
In a newly developed innovative idea brought up by CSIR in India, gas turbine exhaust gas are being utilized to convert feedwater into steam. Certain data of the experiment are as follows: mass flow rate of exhaust gas = 40 kg/hr, enthalpy of exhaust gas at the time of their exit from gas turbine is 600 kJ/kg, steam turbine output as measured by brake dynamometer = 60 hp-sec, thermal efficiency of steam power plant is 0.25, efficiency of exhaust gas in converting feedwater into steam is taken as 50%. Find the enthalpy of exhaust gas remaining after they generate steam from feedwater?
Read the passage carefully and choose the best answer to each question out of the four alternatives and click the button corresponding to it. The first working steam­ powered vehicle was designed and most likely built by Ferdinand Verbies, a Flemish member of a Jesuit mission in China around 1672. It was a 65 cm long scale­ model toy for the Chinese Emperor, that was unable to carry a driver or a passenger. It is not known if Verbiest's model was ever built. Nicolas- Joseph Cugnot is widely credited with building the first full­ scale, self ­propelled mechanical vehicle or automobile in about 1769; he also created a steam­ powered tricycle. He constructed two steam tractors for the French Army, one of which is preserved in the French National Conservatory of Arts and Crafts. His inventions were however handicapped by problems of water supply and maintaining steam pressure. In 1801, Richard Trevithick built and demonstrated his Puffing Devil road locomotive, believed by many to be the first demonstration of a steam ­powered road vehicle. It was unable to maintain sufficient steam pressure for long periods. Sentiment against steam ­powered road vehicles led to the Locomotive Acts of 1865. In 1807 Nicephore Niepce and his brother Claude probably created the world's first internal combustion engine which they called Pyreolophore. The first full­scale, working steam ­powered tricycle was built by:
Read the passage carefully and choose the best answer to each question out of the four alternatives and click the button corresponding to it. The first working steam­ powered vehicle was designed and most likely built by Ferdinand Verbies, a Flemish member of a Jesuit mission in China around 1672. It was a 65 cm long scale­ model toy for the Chinese Emperor, that was unable to carry a driver or a passenger. It is not known if Verbiest's model was ever built. Nicolas- Joseph Cugnot is widely credited with building the first full­ scale, self ­propelled mechanical vehicle or automobile in about 1769; he also created a steam­ powered tricycle. He constructed two steam tractors for the French Army, one of which is preserved in the French National Conservatory of Arts and Crafts. His inventions were however handicapped by problems of water supply and maintaining steam pressure. In 1801, Richard Trevithick built and demonstrated his Puffing Devil road locomotive, believed by many to be the first demonstration of a steam ­powered road vehicle. It was unable to maintain sufficient steam pressure for long periods. Sentiment against steam ­powered road vehicles led to the Locomotive Acts of 1865. In 1807 Nicephore Niepce and his brother Claude probably created the world's first internal combustion engine which they called Pyreolophore. Cugnot built steam tractors for:
Consider the following statements in connection with hydraulic turbines: 1. The Kaplan turbine is a radial flow turbine in which the guide vane angles as well as the runner vane angles are adjustable. 2. Francis and Kaplan turbines are provided with draft tubes which carry water from exit of runner to tail water to increase the gross head across the turbine. 3. The parts of turbines susceptible to cavitation are the guide vanes and runner vanes – drastically reducing the turbine efficiency. 4. The specific speed of a 4-jet Pelton turbine will be 28 if the specific speed of a single-jet Pelton turbine is 14. Which of the above statements are correct?