The superheat or degree of superheat is given by

The superheat or degree of superheat is given by Correct Answer difference between the temperature of superheated vapour and saturation temperature

Superheat= T1(temperature of superheated vapour) – T(saturated).
Bissoy MCQ

Related Questions

Let D be a simple graph on 10 vertices such that there is a vertex of degree 1, a vertex of degree 2, a vertex of degree 3, a vertex of degree 4, a vertex of degree 5, a vertex of degree 6, a vertex of degree 7, a vertex of degree 8 and a vertex of degree 9. What can be the degree of the last vertex?
The rear window of an automobile is made of thick glass i.e. AB = 5 mm and thermal conductivity is 0.8 W/m degree. To defrost this window, a thin transparent film type heating element has been fixed to its inner surface. For the conditions given below, determine the electric power that must be provided per unit area of window if a temperature 5 degree Celsius is maintained at its outer surface. Interior air temperature and the corresponding surface coefficient are 20 degree Celsius and 12 W/m2 degree. Surrounding air temperature and the corresponding surface coefficient are – 15 degree Celsius and 70 W/m2 degree. Electric heater provides uniform heat flux
During heat treatment, cylindrical pieces of 25 mm diameter, 30 mm height and at 30 degree Celsius are placed in a furnace at 750 degree Celsius with convective coefficient 80 W/m2 degree. Calculate the time required to heat the pieces to 600 degree Celsius. Assume the following property values Density = 7850 kg /m3 Specific heat = 480 J/kg K Conductivity = 40 W/m degree
A water line is buried underground in dry soil that has an assumed initial temperature of 4.5 degree Celsius. The pipe may have no flow through it for long period of time, yet it will not be drained in order that no freezing occurs, the pipe must be kept at a temperature not lower than 0 degree Celsius. The pipe is to be designed for a 30 hour period at the beginning of which the soil surface temperature suddenly drops to – 17 degree Celsius. Workout the minimum earth covering needed above the water pipe so as to prevent the possibility of freezing during 36 hour cold spell. The soil in which the pipe is buried has the following properties Density = 640 kg/m3 Specific heat = 1843J/kg degree Thermal conductivity = 0.345 W/m degree
Directions : In each of the following questions a statement is given, followed by two conclusions. Give answer :

Statements : The eligibility for admission to the course is minimum second class Master's degree. However, the candidates who have appeared for the final year examination of Master's degree can also apply.

Conclusions :
I. All candidates who have yet to get their Master's degree will be there in the list of selected candidates.
II. All candidates having obtained second class Master's degree will be there in the list of selected candidates.
A 25 mm diameter egg roll (k = 1 W/m degree) is roasted with the help of microwave heating. For good quality roasting, it is desired that temperature at the center of roll is maintained at 100 degree Celsius when the surrounding temperature is 25 degree Celsius. What should be the heating capacity in W/m 3 of the microwave if the heat transfer coefficient on the surface of egg roll is 20 W/m2 degree?
Exhaust gases (c P = 1.12 k J/kg K) flowing through a tubular heat exchanger at the rate of 1200 kg/hr are cooled from 400 degree Celsius to 120 degree Celsius. This cooling is affected by water (c P = 4.18 k J/kg K) that enters the system at 10 degree Celsius at the rate of 1500 kg/hr. If the overall heat transfer coefficient is 500 k J/m2 hr degree, what heat exchanger area is required to handle the load for counter flow arrangement?
Find the heat flow rate through the composite wall as shown in figure. Assume one dimensional flow and take k 1 = 150 W/m degree k 2 = 30 W/m degree k 3 = 65 W/m degree k 4 = 50 W/m degree AB = 3 cm, BC = 8 cm and CD = 5 cm. The distance between middle horizontal line from the top is 3 cm and from the bottom is 7 cm
A cable of 10 mm outside is to be laid in an atmosphere of 25 degree Celsius (h = 12.5 W/m2 degree) and its surface temperature is likely to be 75 degree Celsius due to heat generated within it. How would the heat flow from the cable be affected if it is insulated with rubber having thermal conductivity k = 0.15 W/m degree?
A composite slab consists of 5 cm thick layer of steel (k = 146 kJ/m hr degree) on the left side and a 6 cm thick layer of brass (k = 276 kJ/m hr degree) on the right hand side. The outer surfaces of the steel and brass are maintained at 100 degree Celsius and 50 degree Celsius. The contact between the two slabs is perfect and heat is generated at the rate of 4.2 * 10 5 k J/m2 hr at the plane of contact. The heat thus generated is dissipated from both sides of composite slab for steady state conditions. Calculate the temperature at the interface