Bissoy.com
Doctors Medicines MCQs Q&A

Consider the following statements: 1. A stub tooth has a working depth larger than that of a full-depth tooth. 2. The path of contact for involute gears is an arc of a circle. Which of the statements given above is/are correct?

Consider the following statements: 1. A stub tooth has a working depth larger than that of a full-depth tooth. 2. The path of contact for involute gears is an arc of a circle. Which of the statements given above is/are correct? Correct Answer Neither 1 nor 2

1. A stub tooth has a working depth lower than that of a full-depth tooth. 2. The path of contact for involute gears is a line.

Related Questions

Consider the following statements: In case of helical gears, teeth are cut at an angle to the axis of rotation of the gears. 1) Helix angle introduces another ratio called axial contact ratio. 2) Transverse contact ratio is equal to axial contact ratio in helical gears. 3) Large transverse contact ratio does not allow multiple teeth to share the load. 4) Large axial contact ratio will cause larger axial force component Which of the above statements are correct?
Which of the following statements is/are true? A: If a circle is formed from a wire, which was initially in the shape of a semi-circle, then ratio of radius of circle and that of semi-circle will be 7: 11. B: If in a semi-circle of radius ‘r’, another semi-circle of radius ‘4r/5’ is drawn, then area of the remaining part of larger semi-circle will be ‘3πr2/5’. C: In a circle of radius ‘r’, if ‘O’ is the center of circle and radii OA and OB are at the angle of 45°, then the length of major arc AB will be ‘7πr/8’.
Consider the following statements: 1. In spur gears, the contact occurs abruptly on a line parallel to the axis, and the disengagement too is abrupt. 2. In helical gears, both loading and unloading are gradual, and therefore, these happen more smoothly and less noisily 3. When two gears mesh, any arbitrary shape of the tooth can be chosen for the profile of the teeth of any one of the two gears, and the profile for the other shall be obtained by applying the law of gearing. Which of the above statements are correct?
Two involute gears in a mesh have path of approach = 29.83 mm and path of recess = 21.09 mm. The larger gear has 40 teeth and the pinion has 12 teeth. Find the ratio of the sliding to rolling velocity at the: i) beginning of contact ii) end of contact iii) pitch point r = 72 mm
Steps given are to draw an involute of a given triangle ABC. Arrange the steps. i. With C as centre and radius C1 draw arc cutting AC-extended at 2. ii. With A as center and radius A2 draw an arc cutting BA- extended at 3 completing involute. iii. B as centre with radius AB draw an arc cutting the BC- extended at 1. iv. Draw the given triangle with corners A, B, C.
Consider the following statements regarding gear tooth designing for gear drive: 1. Tooth profiles not designed as per ‘law of gearing’ will cause vibration and impact problems even at low speed. 2. As the gears go through their mesh, the pitch point must remain stationary on the line of centres. 3. In a correctly designed tooth profile, the line of action of successive instantaneous points of contact will pass through the stationary pitch point. Which of the above statements are correct?
Steps are given to draw involute of given circle. Arrange the steps f C is the centre of circle and P be the end of the thread (starting point). i. Draw a line PQ, tangent to the circle and equal to the circumference of the circle. ii. Draw the involute through the points P1, P2, P3 ……..etc. iii. Divide PQ and the circle into 12 equal parts. iv. Draw tangents at points 1, 2, 3 etc. and mark on them points P1, P2, P3 etc. such that 1P1 =P1l, 2P2 = P2l, 3P3= P3l etc.
Two involute gears are designed to mesh for a given centre distance and a given angular velocity ratio (other than 1). During assembly, the centre distance has increased slightly. Then which of the following changes occur? (i) Velocity ratio changes (ii) Pressure angle changes (iii) Pitch circle diameter changes (iv) Working depth changes (v) Base circle radius changes Select the correct answer using the code given below.
Consider a circle of radius 4 cm such that  A1, A2, A3, A4, A5, A6 are 6 points in the given order on the circle. The length of the arc AxAx + 1 is 1/3 times the length of the arc Ax + 1Ax + 2. If the circumference of the circle is 6 times the sum of the lengths of the 5 arcs then what is the angle subtended by the arc A2A3 at the center of the circle? 
Two involute gears have path of contact 40 mm and the pressure angle is 50°. Find the arc of contact.