Related Questions

The frictional torque transmitted by a cone clutch is same as that of
A flat pivot bearing
B flat collar bearing
C conical pivot bearing
D trapezoidal pivot bearing
A semicircular disc rests on a horizontal surface with its top flat surface horizontal and circular portion touching down. The coefficient of friction between semi circular disc and horizontal surface is µ. This disc is to be pulled by a horizontal force applied at one edge and it always remains horizontal. When the disc is about to start moving, its top horizontal force will
A Remain horizontal
B Slant up towards direction of pull
C Slant down towards direction of pull
D None of the above
A disc is a spinning with an angular velocity $$\omega $$ rad/s about the axis of spin. The couple applied to the disc causing precession will be (where $$I$$ = Mass moment of inertia of the disc and $$\omega {\text{P}}$$  = Angular velocity of precession of the axis of spin)
A $$\frac{1}{2}I{\omega ^2}$$
B $$I{\omega ^2}$$
C $$\frac{1}{2}I\omega \omega {\text{P}}$$
D $$I\omega \omega {\text{P}}$$
The frictional torque transmitted in a conical pivot bearing, considering uniform wear, is
A 1/2 × μ.W. R cosec α
B 2/3 × μ.W. R cosec α
C 3/4 × μ.W. R cosec α
D μ.W.R cosec α
The frictional torque transmitted in a conical pivot bearing with assumption of uniform pressure is __________ as compared to uniform wear.
A Less
B More
C Same
D None of these
The frictional torque transmitted in a flat pivot bearing with assumption of uniform pressure is _________ as compared to uniform wear.
A Less
B More
C Same
D None of these
The frictional torque transmitted in a truncated conical pivot bearing, considering uniform wear, is
A $$\frac{1}{2}\mu {\text{Wcosec}}\alpha \left( {{{\text{r}}_1} + {{\text{r}}_2}} \right)$$
B $$\frac{2}{3}\mu {\text{Wcosec}}\alpha \left( {{{\text{r}}_1} + {{\text{r}}_2}} \right)$$
C $$\frac{1}{2}\mu {\text{Wcosec}}\alpha \left( {\frac{{{\text{r}}_1^3 - {\text{r}}_2^3}}{{{\text{r}}_1^2 - {\text{r}}_2^2}}} \right)$$
D $$\frac{2}{3}\mu {\text{Wcosec}}\alpha \left( {\frac{{{\text{r}}_1^3 - {\text{r}}_2^3}}{{{\text{r}}_1^2 - {\text{r}}_2^2}}} \right)$$
The frictional torque transmitted in a flat pivot bearing, considering uniform wear, is (where μ = Coefficient of friction, W = Load over the bearing and R = Radius of bearing surface)
A $$\frac{1}{2}$$μWR
B $$\frac{2}{3}$$μWR
C $$\frac{3}{4}$$μWR
D μWR
The frictional torque transmitted in a truncated conical pivot bearing, considering uniform pressure, is
A $$\frac{1}{2}\mu {\text{Wcosec}}\alpha \left( {{{\text{r}}_{\text{1}}} + {{\text{r}}_{\text{2}}}} \right)$$
B $$\frac{2}{3}\mu {\text{Wcosec}}\alpha \left( {{{\text{r}}_{\text{1}}} + {{\text{r}}_{\text{2}}}} \right)$$
C $$\frac{1}{2}\mu {\text{Wcosec}}\alpha \left( {\frac{{{\text{r}}_1^3 - {\text{r}}_2^3}}{{{\text{r}}_1^2 - {\text{r}}_2^2}}} \right)$$
D $$\frac{2}{3}\mu {\text{Wcosec}}\alpha \left( {\frac{{{\text{r}}_1^3 - {\text{r}}_2^3}}{{{\text{r}}_1^2 - {\text{r}}_2^2}}} \right)$$
The frictional torque transmitted in a conical pivot bearing, considering uniform pressure, is (where R = Radius of shaft and $$\alpha $$ = Semi-angle of the cone)
A $$\frac{1}{2}\mu {\text{WRcosec}}\alpha $$
B $$\frac{2}{3}\mu {\text{WRcosec}}\alpha $$
C $$\frac{3}{4}\mu {\text{WRcosec}}\alpha $$
D $$\mu {\text{WRcosec}}\alpha $$

Next steps