The brake shown in figure has a coefficient of friction 0.25 and is to operate using a maximum force F of 500 N. Assume width of the band to be 50 mm. Find the maximum band tension. All dimensions are in mm.

The brake shown in figure has a coefficient of friction 0.25 and is to operate using a maximum force F of 500 N. Assume width of the band to be 50 mm. Find the maximum band tension. All dimensions are in mm. Correct Answer 4449.6 N

ΣMo = 0 = 115P2 – 365F = 0 P2 = 1586.96N α = 33.59° Φ = 270 – 33.59 = 4.126 radians P1 = 4449.6N.
Bissoy MCQ

Related Questions

The brake shown in figure has a coefficient of friction 0.25 and is to operate using a maximum force F of 500 N. Assume width of the band to be 50 mm, find the braking torque.
In a differential band brake as shown in the below figure, the drum rotates anticlockwise and the greater tension T1 acts at A and smaller tension T2 at B. Length OA is greater than length OB. In order to apply the brake, the force P at C should
Theory of Machine mcq question image
From an alloy, two specimens are machined and tested separately under tension and compression. The engineering stress-strain curves as well as the true stress-true strain curves for tension and compression are plotted in the same diagram. Identify the correct statements:
P. The engineering stress-strain curves in tension and compression are identical.
Q. The true stress-true strain curve in compression is lower than the true stresstrue strain curve in tension due to Bauschinger effect.
R. The true stress-true strain curve in tension is above the corresponding engineering stress-strain, curve.
S. The true stress-true strain curve in tension and compression are identical.
A pivoted double block brake has a drum radius of 280mm with two shoes subtending an angle of 100⁰. Maximum pressure intensity is 0.5N/mm². If the width of friction lining is 90mm, find the torque capacity f each shoe. Assume coefficient of friction as 0.2.
A pivoted double block brake has a drum radius of 280mm with two shoes subtending an angle of 100⁰. Maximum pressure intensity is 0.5N/mm². If the width of friction lining is 90mm, find the reaction at pivot in horizontal direction. Assume coefficient of friction as 0.2.
A multiple disc clutch has five plates having four pairs of active friction surfaces. If the intensity of pressure is not to exceed 0.127 N/mm2, find the power transmitted at 500 r.p.m. The outer and inner radii of friction surfaces are 125 mm and 75 mm respectively. Assume uniform wear and take coefficient of friction = 0.3.
A metallic sheet 1 m wide and 10 mm thick is to be rolled under a front tension force of 100 KN. A specimen from the sheet, tested under tension, shows a yield stress of 100 MPa. Assume plain strain condition during rolling and ignore the friction. If yielding is assumed to start at a roll pressure of σ3 MPa, then the stress in the width direction (where strain is zero) is
What is the braking torque at leading shoe if resultant frictional force acts at a distance of 250 mm from the brake drum center, coefficient of friction between the shoe and the drum as 0.5, the free ends of the two shoes are pushed apart with a force of 300 N which is acting at a distance of 320 mm from anchor, and two shoes are anchored together 170 mm away from the brake drum center?
A single cylinder, four stroke cycle oil engine is fitted with a rope brake. The diameter of the brake wheel is 600 mm and the rope diameter is 26 mm. The dead load on the brake is 200 N and the spring balance reads 30 N. If the engine runs at 450 r.p.m., what will be the brake power of the engine?
For the given figure, the brake can sustain a torque of 350 N-m and coefficient of friction between the band and drum is 0.3, find necessary force required for clockwise rotation of the drum in N.