Bissoy.com
Doctors Medicines MCQs Q&A

The material used for the brake lining should have

The material used for the brake lining should have Correct Answer All of the mentioned

The material used for the brake lining should have the following characteristics: 1. It should have high coefficient of friction with minimum fading. 2. It should have low wear rate. 3. It should have high heat resistance. 4. It should have high heat dissipation capacity. 5. It should have adequate mechanical strength. 6. It should not be affected by moisture and oil.

Related Questions

A single cylinder, four stroke cycle oil engine is fitted with a rope brake. The diameter of the brake wheel is 600 mm and the rope diameter is 26 mm. The dead load on the brake is 200 N and the spring balance reads 30 N. If the engine runs at 450 r.p.m., what will be the brake power of the engine?
If L is total length of a canal in kilometers, P is total perimeter of its lining in metres and C is the cost of lining per square metre, the additional expenditure involved on lining, is
The material used for brake lining should have __________ coefficient of friction.
How much is the torque developed if a 400 V DC shunt motor gave the following readings during the brake test: Length of brake arm = 200 cm Reading of spring balance at the end of brake arm = 40 kg­-wt Supply voltage = 400 V
The brake power (B.P.) of the engine is given by (where W = Brake load or dead load in newtons, l = Length of arm in meters, N = Speed of engine in r.p.m., S = Spring balance reading in newtons, D = Dia. of brake drum in meters, and d = Dia. of rope in meters)
A 25 kg mass moving with 25 m/s is brought to a complete stop with a constant deceleration over a period of 5 seconds by a brake system. The brake energy is absorbed by 0.5kg water initially at 100 kPa, 20°C. Assume that the mass is at constant P and T. Find the energy the brake removes from the mass assuming P = C.
The brake power (B.P.) of the engine is given by (where W = Brake load or dead load in newtons, $$l$$ = Length of arm in meters, N = Speed of engine in r.p.m., S = Spring balance reading in newtons, D = Diameter of brake drum in meters and d = Diameter of rope in meters)
Which type of lining is only used for lining the side slopes of the canal?
The given conditions are imposed by an officer for providing the Travelling Concession to the employees. The employee A. Should have made 2 trips in a 4 calendar years. B. Should have made one trip in 1 calendar year. C. Should have made one trip within the native country, while the other could have been overseas. D. Should have made a trip with maximum of 6 people. E. The total cost of both the trips should not have exceeded Rs. 6 lakhs. In case of employee who satisfies all the other criteria except: I. At (D) above, he/she would get Rs. 4 lakhs as concession. II. At (E) above, he/she would get Rs. 3 lakhs as concession. In the inquiry underneath, data of one employee is given. You need to take one of the accompanying four choices in the light of the data given and the criteria and conditions given above. Shyam, a native of India, along with his wife and 2 children went for vacations within India. He made his first trip in February, 2016 and second one in August 2016. The total expenditure of the trips were four lakhs and forty thousand.
In the question below is given a statement followed by two courses of action numbered I and II. You have to assume everything given in the statement to be true and then decide which of the given/ suggested courses of action logically follows for pursuing. Statement: One of the problems of the public food- processing industry is the irregular supply of raw material to other industries also. Courses of Action:  The government should deregulate the supply of raw material for the food processing industry. The government should announce an attractive package to ensure regular supply of raw material. The producers of raw material are not getting a reasonable price