Bissoy.com
Doctors Medicines MCQs Q&A

After expansion from a gas turbine, the hot exhaust gases are used to heat the compressed air from a compressor with the help of a cross flow heat exchanger of 0.8 effectiveness. What is the number of transfer units of the heat exchanger?

After expansion from a gas turbine, the hot exhaust gases are used to heat the compressed air from a compressor with the help of a cross flow heat exchanger of 0.8 effectiveness. What is the number of transfer units of the heat exchanger? Correct Answer 4

Effectiveness = NTU/NTU – 1 = 0.5.

Related Questions

In a newly developed innovative idea brought up by CSIR in India, gas turbine exhaust gas are being utilized to convert feedwater into steam. Certain data of the experiment are as follows: mass flow rate of exhaust gas = 40 kg/hr, enthalpy of exhaust gas at the time of their exit from gas turbine is 600 kJ/kg, steam turbine output as measured by brake dynamometer = 60 hp-sec, thermal efficiency of steam power plant is 0.25, efficiency of exhaust gas in converting feedwater into steam is taken as 50%. Find the enthalpy of exhaust gas remaining after they generate steam from feedwater?
The rate of electricity in the rural area is given below: i) up to 25 units - Rs 5 per unit ii) up to 75 units - Rs 7 per units iii) up to 100 units - Rs 9 per units iv) After 100 units - Rs 13 per units Additional charge after 100 units = Rs. 50 The consumption of the electricity of the household is 120 units. How much electricity bill he has to pay?
An operating system uses the Banker’s algorithm for deadlock avoidance when managing the allocation of three resource types X, Y, and Z to three processes P0, P1, and P2. The table given below presents the current system state. Here, the Allocation matrix shows the current number of resources of each type allocated to each process and the Max matrix shows the maximum number of resources of each type required by each process during its execution.   Allocation Max   X Y Z X Y Z P0 0 0 1 8 4 3 P1 3 2 0 6 2 0 P2 2 1 1 3 3 3   There are 3 units of type X, 2 units of type Y and 2 units of type Z still available. The system is currently in a safe state. Consider the following independent requests for additional resources in the current state: REQ1: P0 requests 0 units of X, 0 units of Y and 2 units of Z REQ2: P1 requests 2 units of X, 0 units of Y and 0 units of Z Which one of the following is TRUE?
Which of the following statement(s) is/are incorrect? (i) A turbine is called an impulse turbine if at the inlet of the turbine total energy is only kinetic energy (ii) A turbine is called a reaction turbine if at the inlet of the turbine the total energy is kinetic energy and pressure energy (iii) The inward flow reaction turbine having radial discharge at the outlet is known as Kaplan turbine
A heat exchanger with heat transfer surface area A and overall heat transfer coefficient U handles two fluids of heat capacities Cmax and Cmin. The number of transfer units (NTU) used in the analysis of heat exchanger is specified as
A heat exchanger with heat transfer surface area A and overall heat transfer coefficient U handles two fluids of heat capacities Cmax and Cmin. The number of transfer units (NTU) used in the analysis of heat exchanger is specified as
Fresh air at 14.7psi enters a compressor of a gas turbine and is compressed isentropically. The gas at the mouth of turbine is at 60 psi pressure and with a specific volume as 50 m3/kg. What would be the specific volume of fresh air?
Which of the following statements are correct? 1) Velocity compounded impulse turbine gives less speed and less efficiency. 2) For an ideal centrifugal compressor, the pressure produced depends on impeller velocity and diameter. 3) While flowing through the rotor blades in a gas turbine, the relative velocity of gas continuously decreases. 4) While flowing through the rotor blades in an axial flow compressor, the relative velocity of air continuously decreases.
Exhaust gases (c P = 1.12 k J/kg K) flowing through a tubular heat exchanger at the rate of 1200 kg/hr are cooled from 400 degree Celsius to 120 degree Celsius. This cooling is affected by water (c P = 4.18 k J/kg K) that enters the system at 10 degree Celsius at the rate of 1500 kg/hr. If the overall heat transfer coefficient is 500 k J/m2 hr degree, what heat exchanger area is required to handle the load for counter flow arrangement?
Exhaust gases (c P = 1.12 k J/kg K) flowing through a tubular heat exchanger at the rate of 1200 kg/hr are cooled from 400 degree Celsius to 120 degree Celsius. This cooling is affected by water (c P = 4.18 k J/kg K) that enters the system at 10 degree Celsius at the rate of 1500 kg/hr. If the overall heat transfer coefficient is 500 k J/m2 hr degree, what heat exchanger area is required to handle the load for parallel flow arrangement?