Bissoy.com
Doctors Medicines MCQs Q&A

Saturated steam is allowed to condense over a vertical flat surface and the condensate film flows down the surface. The local coefficient of heat transfer for condensation

Saturated steam is allowed to condense over a vertical flat surface and the condensate film flows down the surface. The local coefficient of heat transfer for condensation Correct Answer Decreases with increasing distance from the top of the surface

It decreases with increasing thickness of condensate film.

Related Questions

The condensate film runs down a vertical flat surface where saturated steam is allowed to condense. Condensation’s local coefficient of heat transfer
In a surface condenser, the water flowing through a series of tubes at the rate of 200 kg/hr is heated from 15 degree Celsius to 75 degree Celsius. The steam condenses on the outside surface of tubes at atmospheric pressure and the overall heat transfer coefficient is estimated at 860 k J/m2 hr degree. Find the number of transfer units of the heat exchanger. At the condensing pressure, stream has saturation temperature 0f 100 degree Celsius and the latent heat of vaporization is 2160 k J/kg. Further, the steam is initially just saturated and the condensate leaves the exchanger without sub-cooling i.e. only latent heat of condensing steam is transferred to water. Take specific heat of water as 4 k J/kg K
A two pass surface condenser is required to handle the exhaust from a turbine developing 15 MW with specific steam consumption of 5 kg/k W h. The quality of exhaust steam is 0.9, the condenser vacuum is 66 cm of mercury while the bar meter reads 76 cm of mercury. The condenser tubes are 28 mm inside diameter, 4 mm thick and water flows through tubes with a speed of 3 m/s and inlet temperature 20 degree Celsius. All the steam is condensed, the condensate is saturated water and temperature of cooling water at exit is 5 degree Celsius less than the condensate temperature. Assuming that overall coefficient of heat transfer is 4 k W/m2 degree, determine the mass of cooling water circulated
In a surface condenser, the water flowing through a series of tubes at the rate of 200 kg/hr is heated from 15 degree Celsius to 75 degree Celsius. The steam condenses on the outside surface of tubes at atmospheric pressure and the overall heat transfer coefficient is estimated at 860 k J/m2 hr degree. Find the effectiveness of the heat exchanger. At the condensing pressure, stream has a saturation temperature 0f 100 degree Celsius and the latent heat of vaporization is 2160 k J/kg. Further, the steam is initially just saturated and the condensate leaves the exchanger without sub-cooling i.e. only latent heat of condensing steam is transferred to the water. Take specific heat of water as 4 k J/kg K
Which are the correct statements? (a) Film condensation usually occur on oily surface. (b) Temperature of condensate gradually increases towards the liquid-vapour interface. (c) Suitable coating is used to promote dropwise condensation. (d) Dropwise condensation gives lower heat transfer rate than film condensation.
A stream of air at 100 kPa pressure and 300 K is flowing on the top surface of a thin flat sheet of solid naphthalene of length 0.2 m with a velocity of 20 m/sec. The other data are: Mass diffusivity of naphthalene vapor in air = 6 * 10 –6 m2/sec Kinematic viscosity of air = 1.5 * 10 –5 m2.sc Concentration of naphthalene at the air-solid naphthalene interface = 1 * 10 – 5 kmol/m3 Calculate the overage mass transfer coefficient over the flat plate. Note: For heat transfer over a flat plate, convective heat transfer coefficient for laminar flow can be calculated by the equation. Nu = 0.664 ReL1/2 Pr1/3 you may use analogy between mass and heat transfer.
Experimental results indicate that the local heat transfer coefficient h g for flow over a flat plate with an extremely rough surface is approximated by the relation h x = a x -0.12 Where a is a constant coefficient and x is distance from the leading edge of the plate. What is the relation between this local heat transfer coefficient and the average heat transfer coefficient for a plate of length x?
Statement 1: Film-type condensation has a higher heat transfer co-efficient than drop-wise condensation. Statement 2: Drop-wise condensation is easier to maintain than Film-type condensation
Consider the following statements (i) If a condensing liquid does not wet a surface, then drop wise condensation will not take place on it (ii) Drop wise condensation gives a higher transfer rate than film wise condensation (iii) Reynolds number of condensing liquid is based on its mass flow rate (iv) Suitable coating or vapor additive is used to promote film wise condensation Identify the correct statement
The average heat transfer co-efficient for laminar film condensation on vertical surface is inversely proportional to (where, ΔT = Temperature drop across condensate film )