Bissoy.com
Doctors Medicines MCQs Q&A

The oil pan of 1.6 engine approximates a flat plate 0.3 m wide by 0.45 m long and protrudes below the framework of the automobile. The engine oil is at 95 degree Celsius and the ambient air temperature is 35 degree Celsius. If the automobile runs at 36 km/hr, make calculations for the rate of heat transfer from the oil-pan surface. Assume negligible resistance to conduction through the oil pan

The oil pan of 1.6 engine approximates a flat plate 0.3 m wide by 0.45 m long and protrudes below the framework of the automobile. The engine oil is at 95 degree Celsius and the ambient air temperature is 35 degree Celsius. If the automobile runs at 36 km/hr, make calculations for the rate of heat transfer from the oil-pan surface. Assume negligible resistance to conduction through the oil pan Correct Answer 170.37 W

Q = h A d t, where h = (Nu) (k)/l and Nu = 0.664 (Re) 0.5 (Pr).33.

Related Questions

The rear window of an automobile is made of thick glass i.e. AB = 5 mm and thermal conductivity is 0.8 W/m degree. To defrost this window, a thin transparent film type heating element has been fixed to its inner surface. For the conditions given below, determine the electric power that must be provided per unit area of window if a temperature 5 degree Celsius is maintained at its outer surface. Interior air temperature and the corresponding surface coefficient are 20 degree Celsius and 12 W/m2 degree. Surrounding air temperature and the corresponding surface coefficient are – 15 degree Celsius and 70 W/m2 degree. Electric heater provides uniform heat flux
In a surface condenser, the water flowing through a series of tubes at the rate of 200 kg/hr is heated from 15 degree Celsius to 75 degree Celsius. The steam condenses on the outside surface of tubes at atmospheric pressure and the overall heat transfer coefficient is estimated at 860 k J/m2 hr degree. Find the number of transfer units of the heat exchanger. At the condensing pressure, stream has saturation temperature 0f 100 degree Celsius and the latent heat of vaporization is 2160 k J/kg. Further, the steam is initially just saturated and the condensate leaves the exchanger without sub-cooling i.e. only latent heat of condensing steam is transferred to water. Take specific heat of water as 4 k J/kg K
A stream of air at 100 kPa pressure and 300 K is flowing on the top surface of a thin flat sheet of solid naphthalene of length 0.2 m with a velocity of 20 m/sec. The other data are: Mass diffusivity of naphthalene vapor in air = 6 * 10 –6 m2/sec Kinematic viscosity of air = 1.5 * 10 –5 m2.sc Concentration of naphthalene at the air-solid naphthalene interface = 1 * 10 – 5 kmol/m3 Calculate the overage mass transfer coefficient over the flat plate. Note: For heat transfer over a flat plate, convective heat transfer coefficient for laminar flow can be calculated by the equation. Nu = 0.664 ReL1/2 Pr1/3 you may use analogy between mass and heat transfer.
In a surface condenser, the water flowing through a series of tubes at the rate of 200 kg/hr is heated from 15 degree Celsius to 75 degree Celsius. The steam condenses on the outside surface of tubes at atmospheric pressure and the overall heat transfer coefficient is estimated at 860 k J/m2 hr degree. Find the effectiveness of the heat exchanger. At the condensing pressure, stream has a saturation temperature 0f 100 degree Celsius and the latent heat of vaporization is 2160 k J/kg. Further, the steam is initially just saturated and the condensate leaves the exchanger without sub-cooling i.e. only latent heat of condensing steam is transferred to the water. Take specific heat of water as 4 k J/kg K
Ambient air at 20 degree Celsius flows past a flat plate with a sharp leading edge at 3 m/s. The plate is heated uniformly throughout its entire length and is maintained at a surface temperature of 40 degree Celsius. Calculate the local convective heat transfer coefficient. Assume that transition occurs at a critical Reynolds number of 500000
Air at 20 degree Celsius flows over a flat plate maintained at 75 degree Celsius. Measurements shows that temperature at a distance of 0.5 mm from the surface of plate is 50 degree Celsius. Presuming thermal conductivity of air is 0.0266 W/m K, estimate the value of local heat transfer coefficient
A centrifugal pump which circulates a hot liquid metal at 500 degree Celsius is driven by a 3600 rpm electric motor. The motor is coupled to the pump impeller by a horizontal steel shaft of dia 25 mm. Let us assume the motor temperature as 60 degree Celsius with the ambient air at 25 degree Celsius, what length of shaft should be specified between the motor and the pump? It may be presumed that the thermal conductivity of the shaft material is 35W/m K and that the convective film coefficient between the steel shaft and the ambient air is 15.7W/square m K
Air at 30 degree Celsius temperature flows at 45 m/s past a wet flat plate of length 0.5 m. Estimate the value of mass transfer coefficient. Assume that the water vapor content of air initially is negligible and take the following thermos-physical properties of air D = 0.256 * 10 -4 m2/s µ = 1.86 * 10 -5 kg/m s c p = 1.005 k J/kg degree Celsius p r = 0.701 p =1.165 kg/m3
Air at 25 degree Celsius approaches a 0.9 m long and 0.6 m wide flat plate with a velocity 4.5 m/s. Let the plate is heated to a surface temperature of 135 degree Celsius. Find local heat transfer coefficient from the leading edge at a distance of 0.5 m
An average convective heat transfer coefficient for flow of air over a sphere has been measured by observing the temperature-time history of a 12 mm diameter copper sphere (density = 9000 kg/m3 and c = 0.4 k J/kg K) exposed to air at 30 degree Celsius. The temperature of the sphere was measured by two thermocouples one located at the center and the other near the surface. The initial temperature of the ball was 75 degree Celsius and it decreased by 10 degree Celsius in 1.2 minutes. Find the heat transfer coefficient