Bissoy.com
Doctors Medicines MCQs Q&A

Three fins of equal length and diameter but made of aluminum, brass and cast iron is heated to 200 degree Celsius at one end. If the fins dissipate heat to the surrounding air at 25 degree Celsius, the temperature at the free end will be least in

Three fins of equal length and diameter but made of aluminum, brass and cast iron is heated to 200 degree Celsius at one end. If the fins dissipate heat to the surrounding air at 25 degree Celsius, the temperature at the free end will be least in Correct Answer Aluminum fin

Thermal conductivity of aluminum is higher than that of others.

Related Questions

An electronic semiconductor device generates 0.16 k J/hr of heat. To keep the surface temperature at the upper safe limit of 75 degree Celsius, it is desired that the heat generated should be dissipated to the surrounding environment which is at 30 degree Celsius. The task is accomplished by attaching aluminum fins, 0.5 square mm and 10 mm to the surface. Work out the number of fins if thermal conductivity of fin material is 690W/m K and the heat transfer coefficient is 45k J/square m hr K. Neglect the heat loss from the tip of the fin
A heating unit is made in the form of a vertical tube of 50 mm outside diameter and 1.2 m height. The tube is fitted with 20 steel fins of rectangular section with height 40 mm and thickness 2.5 mm. The temperature at the base of fin is 75 degree Celsius, the surrounding air temperature is 20 degree Celsius and the heat transfer coefficient between the fin as well as the tube surface and the surrounding air is 9.5 W/m2 K. If thermal conductivity of the fin material is 55 W/m K, find the amount of heat transferred from the tube without fin
A heating unit is made in the form of a vertical tube of 50 mm outside diameter and 1.2 m height. The tube is fitted with 20 steel fins of rectangular section with height 40 mm and thickness 2.5 mm. The temperature at the base of fin is 75 degree Celsius, the surrounding air temperature is 20 degree Celsius and the heat transfer coefficient between the fin as well as the tube surface and the surrounding air is 9.5 W/m2 K. If thermal conductivity of the fin material is 55 W/m K, find the amount of heat transferred from the tube with fin
The rear window of an automobile is made of thick glass i.e. AB = 5 mm and thermal conductivity is 0.8 W/m degree. To defrost this window, a thin transparent film type heating element has been fixed to its inner surface. For the conditions given below, determine the electric power that must be provided per unit area of window if a temperature 5 degree Celsius is maintained at its outer surface. Interior air temperature and the corresponding surface coefficient are 20 degree Celsius and 12 W/m2 degree. Surrounding air temperature and the corresponding surface coefficient are – 15 degree Celsius and 70 W/m2 degree. Electric heater provides uniform heat flux
A motor cycle cylinder consists of ten fins, each 150 mm outside diameter and 75 mm inside diameter. The average fin temperature is 500 degree Celsius and the surrounding air is at 20 degree Celsius temperature. Make calculations for the rate of heat dissipation from the cylinder fins by convection when motor cycle is stationary and convective coefficient is 6 W/m2 K
In a surface condenser, the water flowing through a series of tubes at the rate of 200 kg/hr is heated from 15 degree Celsius to 75 degree Celsius. The steam condenses on the outside surface of tubes at atmospheric pressure and the overall heat transfer coefficient is estimated at 860 k J/m2 hr degree. Find the effectiveness of the heat exchanger. At the condensing pressure, stream has a saturation temperature 0f 100 degree Celsius and the latent heat of vaporization is 2160 k J/kg. Further, the steam is initially just saturated and the condensate leaves the exchanger without sub-cooling i.e. only latent heat of condensing steam is transferred to the water. Take specific heat of water as 4 k J/kg K
In a surface condenser, the water flowing through a series of tubes at the rate of 200 kg/hr is heated from 15 degree Celsius to 75 degree Celsius. The steam condenses on the outside surface of tubes at atmospheric pressure and the overall heat transfer coefficient is estimated at 860 k J/m2 hr degree. Find the number of transfer units of the heat exchanger. At the condensing pressure, stream has saturation temperature 0f 100 degree Celsius and the latent heat of vaporization is 2160 k J/kg. Further, the steam is initially just saturated and the condensate leaves the exchanger without sub-cooling i.e. only latent heat of condensing steam is transferred to water. Take specific heat of water as 4 k J/kg K
A steel strap is serving as a support for the steam pipe. The strap is welded to the pipe and bolted to the ceiling. The junction between the support strut and the ceiling is adiabatic, and the outside temperature of steam pipe is 105 degree Celsius. The strut AB is 60 cm high and AD = BC = 12.5 cm. It is 0.3 cm thick. Workout the rate at which heat is lost to the surrounding air by the support strut. It may be assumed that thermal conductivity for steel is 45 W/m degree, the total outside surface coefficient is 17 W/m2 degree and the surrounding air is at 32 degree Celsius
An average convective heat transfer coefficient for flow of air over a sphere has been measured by observing the temperature-time history of a 12 mm diameter copper sphere (density = 9000 kg/m3 and c = 0.4 k J/kg K) exposed to air at 30 degree Celsius. The temperature of the sphere was measured by two thermocouples one located at the center and the other near the surface. The initial temperature of the ball was 75 degree Celsius and it decreased by 10 degree Celsius in 1.2 minutes. Find the heat transfer coefficient
In a food processing plant, a brine solution is heated from – 12 degree Celsius to – 65 degree Celsius in a double pipe parallel flow heat exchanger by water entering at 35 degree Celsius and leaving at 20.5 degree Celsius. Let the rate of flow is 9 kg/min. Estimate the area of heat exchanger for an overall heat transfer coefficient of 860 W/m2 K. For water c P = 4.186 * 10 3 J/kg K