Bissoy.com
Doctors Medicines MCQs Q&A

A steel rod (k = 30 W/m degree) 1 cm in diameter and 5 cm long protrudes from a wall which is maintained at 10 degree Celsius. The rod is insulated at its tip and is exposed to an environment with h = 50 W/m2 degree and t a = 30 degree Celsius. Calculate the rate of heat dissipation

A steel rod (k = 30 W/m degree) 1 cm in diameter and 5 cm long protrudes from a wall which is maintained at 10 degree Celsius. The rod is insulated at its tip and is exposed to an environment with h = 50 W/m2 degree and t a = 30 degree Celsius. Calculate the rate of heat dissipation Correct Answer 3.658 W

Q = k A m tan h ml (t 0 – t a) = 3.658 W.

Related Questions

A steel rod (k = 30 W/m degree) 1 cm in diameter and 5 cm long protrudes from a wall which is maintained at 10 degree Celsius. The rod is insulated at its tip and is exposed to an environment with h = 50 W/m2 degree and t a = 30 degree Celsius. Calculate the fin efficiency
A copper steel rod (k = 55 W/m degree) has been attached to a plane wall which is maintained at a temperature of 350 degree Celsius. The rod is 8 cm long and has the cross-section of an equilateral triangle with each side 5 mm. Determine the heat dissipation from the rod if it is exposed to a convection environment at 25 degree Celsius with unit surface conductance 100 W/m2 degree. Consider end surface loss to be negligible
A rod of 10 mm diameter and 80 mm length with thermal conductivity 16W/ m K protrudes from a surface at 160 degree Celsius. The rod is exposed to air at 30 degree Celsius with a convective coefficient of 25W/square m K. How does the heat flow from this rod get affected if the same material volume is used for two fins of the same length? Assume short fin with insulated end
A very long copper rod 20 mm in diameter extends horizontally from a plane heated wall maintained at 100 degree Celsius. The surface of the rod is exposed to an air environment at 20 degree Celsius with convective heat transfer coefficient of 8.5 W/m2 degree. Workout the heat loss if the thermal conductivity of copper is 400 W/m degree
A flat wall of fire clay, 50 cm thick and initially at 25 degree Celsius, has one of its faces suddenly exposed to a hot gas at 950 degree Celsius. If the heat transfer coefficient on the hot side is 7.5 W/m2 K and the other face of the wall is insulated so that no heat passes out of that face, determine the time necessary to raise the center of the wall to 350 degree Celsius. For fire clay brick Thermal conductivity = 1.12 W/m K Thermal diffusivity = 5.16 * 10 -7 m2/s
The figure shows a 5 cm diameter rod, 90 cm long, which is having its lower face grinded smooth. The remainder of the rod is exposed to 32 degree Celsius room air and a surface coefficient heat transfer equal to 6.8 W/m2 degree exists between the rod surface and the room air. The grinder dissipates mechanical energy at the rate of 35 W. If thermal conductivity of rod material is 41.5 W/m degree, find the temperature of the rod at the point where the grinding is taking place
A rod of 3 cm diameter and 20 cm length is maintained at 100 degree Celsius at one end and 10 degree Celsius at the other end. These temperature conditions are attained when there is heat flow rate of 6 W. If cylindrical surface of the rod is completely insulated, determine the thermal conductivity of the rod material
The handle of a saucepan, 30 cm long and 2 cm in diameter, is subjected to 100 degree Celsius temperature during a certain cooking operation. The average unit surface conductance over the handle surface is 7.35 W/m2 degree in the kitchen air at 24 degree Celsius. The cook is likely to grasp the last 10 cm of the handle and hence the temperature in this region should not exceed 38 degree Celsius. What should be the thermal conductivity of the handle material to accomplish it? The handle may be treated as a fin insulated at the tip
A steam pipe 50 mm diameter and 2.5 m long has been placed horizontally and exposed to still air at 25 degree Celsius. If the pipe wall temperature is 295 degree Celsius, determine the rate of heat loss. At the mean temperature difference of 160 degree Celsius, the thermo-physical properties of air are k =3.64 * 10 -2 W/m K v =30.09 * 10 -6 m2/s P r =0.682 Β =1/160 + 273 = 2.31 * 10 -3 per K
A composite slab consists of 5 cm thick layer of steel (k = 146 kJ/m hr degree) on the left side and a 6 cm thick layer of brass (k = 276 kJ/m hr degree) on the right hand side. The outer surfaces of the steel and brass are maintained at 100 degree Celsius and 50 degree Celsius. The contact between the two slabs is perfect and heat is generated at the rate of 4.2 * 10 5 k J/m2 hr at the plane of contact. The heat thus generated is dissipated from both sides of composite slab for steady state conditions. Calculate the temperature at the interface