Bissoy.com
Doctors Medicines MCQs Q&A

An 8 cm diameter orange, approximately spherical in shape, undergoes ripening process and generates 18000 k J/m3 hr of energy. If external surface of the orange is at 6.5 degree Celsius, find out the temperature at the center of the orange. Take thermal conductivity = 0.8 k J/ m hr degree for the orange material

An 8 cm diameter orange, approximately spherical in shape, undergoes ripening process and generates 18000 k J/m3 hr of energy. If external surface of the orange is at 6.5 degree Celsius, find out the temperature at the center of the orange. Take thermal conductivity = 0.8 k J/ m hr degree for the orange material Correct Answer 12.5 degree Celsius

q g = 5000 W/m3, k = 0.222 W/m K and t = t W + q g R 2/6K = 12.5 degree Celsius.

Related Questions

The rear window of an automobile is made of thick glass i.e. AB = 5 mm and thermal conductivity is 0.8 W/m degree. To defrost this window, a thin transparent film type heating element has been fixed to its inner surface. For the conditions given below, determine the electric power that must be provided per unit area of window if a temperature 5 degree Celsius is maintained at its outer surface. Interior air temperature and the corresponding surface coefficient are 20 degree Celsius and 12 W/m2 degree. Surrounding air temperature and the corresponding surface coefficient are – 15 degree Celsius and 70 W/m2 degree. Electric heater provides uniform heat flux
The handle of a saucepan, 30 cm long and 2 cm in diameter, is subjected to 100 degree Celsius temperature during a certain cooking operation. The average unit surface conductance over the handle surface is 7.35 W/m2 degree in the kitchen air at 24 degree Celsius. The cook is likely to grasp the last 10 cm of the handle and hence the temperature in this region should not exceed 38 degree Celsius. What should be the thermal conductivity of the handle material to accomplish it? The handle may be treated as a fin insulated at the tip
Two rods A and B of the same length and diameter protrude from a surface at 120 degree Celsius and are exposed at air at 25 degree Celsius. The temperatures measured at the end of the rods are 50 degree Celsius and 75 degree Celsius. If thermal conductivity of material A is 20W/ m K, calculate it for B
A water line is buried underground in dry soil that has an assumed initial temperature of 4.5 degree Celsius. The pipe may have no flow through it for long period of time, yet it will not be drained in order that no freezing occurs, the pipe must be kept at a temperature not lower than 0 degree Celsius. The pipe is to be designed for a 30 hour period at the beginning of which the soil surface temperature suddenly drops to – 17 degree Celsius. Workout the minimum earth covering needed above the water pipe so as to prevent the possibility of freezing during 36 hour cold spell. The soil in which the pipe is buried has the following properties Density = 640 kg/m3 Specific heat = 1843J/kg degree Thermal conductivity = 0.345 W/m degree
A 12 cm diameter cylindrical bar, initially at a uniform temperature of 40 degree Celsius, is placed in a medium at 650 degree Celsius with convective coefficient of 22 W/m2 K. Determine the time required for the center to reach 255 degree Celsius. For the material of the bar: Thermal conductivity = 20 W/m K Density = 580 kg/m3 Specific heat = 1050 J/kg K
A flat wall of fire clay, 50 cm thick and initially at 25 degree Celsius, has one of its faces suddenly exposed to a hot gas at 950 degree Celsius. If the heat transfer coefficient on the hot side is 7.5 W/m2 K and the other face of the wall is insulated so that no heat passes out of that face, determine the time necessary to raise the center of the wall to 350 degree Celsius. For fire clay brick Thermal conductivity = 1.12 W/m K Thermal diffusivity = 5.16 * 10 -7 m2/s
An average convective heat transfer coefficient for flow of air over a sphere has been measured by observing the temperature-time history of a 12 mm diameter copper sphere (density = 9000 kg/m3 and c = 0.4 k J/kg K) exposed to air at 30 degree Celsius. The temperature of the sphere was measured by two thermocouples one located at the center and the other near the surface. The initial temperature of the ball was 75 degree Celsius and it decreased by 10 degree Celsius in 1.2 minutes. Find the heat transfer coefficient
An electronic semiconductor device generates 0.16 k J/hr of heat. To keep the surface temperature at the upper safe limit of 75 degree Celsius, it is desired that the heat generated should be dissipated to the surrounding environment which is at 30 degree Celsius. The task is accomplished by attaching aluminum fins, 0.5 square mm and 10 mm to the surface. Work out the number of fins if thermal conductivity of fin material is 690W/m K and the heat transfer coefficient is 45k J/square m hr K. Neglect the heat loss from the tip of the fin
A cylindrical stainless steel (k = 25 W/m K) ingot, 10 cm in diameter and 25 cm long, passes through a heat treatment furnace which is 5 meter in length. The initial ingot temperature is 90 degree Celsius, the furnace gas is at 1260 degree Celsius and the combined radiant and convective surface coefficient is 100 W/m2 K. Determine the maximum speed with which the ingot moves through the furnace if it must attain 830 degree Celsius temperature. Take thermal diffusivity as 0.45 * 10 -5 m2/s
A spherical vessel of 0.5 m outside diameter is insulated with 0.2 m thickness of insulation of thermal conductivity 0.04 W/m degree. The surface temperature of the vessel is – 195 degree Celsius and outside air is at 10 degree Celsius. Determine heat flow per m2 based on inside area