Bissoy.com
Doctors Medicines MCQs Q&A

A slab of 12 cm thickness and generating heat uniformly at 10 6 W/m3 has thermal conductivity of 200 W/m degree. Both surfaces of the slab are maintained at 150 degree Celsius. Determine the heat flow rate at the quarter planes

A slab of 12 cm thickness and generating heat uniformly at 10 6 W/m3 has thermal conductivity of 200 W/m degree. Both surfaces of the slab are maintained at 150 degree Celsius. Determine the heat flow rate at the quarter planes Correct Answer 30000 W/m2

q g (π R2 L) = (t w – t a) (2 π R L) h.

Related Questions

The rear window of an automobile is made of thick glass i.e. AB = 5 mm and thermal conductivity is 0.8 W/m degree. To defrost this window, a thin transparent film type heating element has been fixed to its inner surface. For the conditions given below, determine the electric power that must be provided per unit area of window if a temperature 5 degree Celsius is maintained at its outer surface. Interior air temperature and the corresponding surface coefficient are 20 degree Celsius and 12 W/m2 degree. Surrounding air temperature and the corresponding surface coefficient are – 15 degree Celsius and 70 W/m2 degree. Electric heater provides uniform heat flux
A 2 cm thick steel slab heated to 525 degree Celsius is held in air stream having a mean temperature of 25 degree Celsius. Estimate the time interval when the slab temperature would not depart from the mean value of 25 degree Celsius by more than 0.5 degree Celsius at any point in the slab. The steel plate has the following thermal physical properties Density = 7950 kg/m3 C P = 455 J/kg K K = 46 W/m K
A composite slab consists of 5 cm thick layer of steel (k = 146 kJ/m hr degree) on the left side and a 6 cm thick layer of brass (k = 276 kJ/m hr degree) on the right hand side. The outer surfaces of the steel and brass are maintained at 100 degree Celsius and 50 degree Celsius. The contact between the two slabs is perfect and heat is generated at the rate of 4.2 * 10 5 k J/m2 hr at the plane of contact. The heat thus generated is dissipated from both sides of composite slab for steady state conditions. Calculate the temperature at the interface
A composite wall is made of two layers of thickness δ1 and δ2 having thermal conductivities k and 2k and equal surface area normal to the direction of heat flow. The outer surface of composite wall are at 100 degree Celsius and 200 degree Celsius. The minimum surface temperature at the junction is 150 degree Celsius. What will be the ratio of wall thickness?
What maximum thickness of concrete can be poured without causing the temperature gradient to exceed 98.5 degree Celsius per meter anywhere in the slab? Consider a 1.2 m thick slab of poured concrete (k = 1.148 W/m degree) with both of side surfaces maintained at a temperature of 20 degree Celsius. During its curing, chemical energy is released at the rate of 80 W/m3. Workout the maximum temperature of concrete
In a food processing plant, a brine solution is heated from – 12 degree Celsius to – 65 degree Celsius in a double pipe parallel flow heat exchanger by water entering at 35 degree Celsius and leaving at 20.5 degree Celsius. Let the rate of flow is 9 kg/min. Estimate the area of heat exchanger for an overall heat transfer coefficient of 860 W/m2 K. For water c P = 4.186 * 10 3 J/kg K
A flat wall of fire clay, 50 cm thick and initially at 25 degree Celsius, has one of its faces suddenly exposed to a hot gas at 950 degree Celsius. If the heat transfer coefficient on the hot side is 7.5 W/m2 K and the other face of the wall is insulated so that no heat passes out of that face, determine the time necessary to raise the center of the wall to 350 degree Celsius. For fire clay brick Thermal conductivity = 1.12 W/m K Thermal diffusivity = 5.16 * 10 -7 m2/s
A water line is buried underground in dry soil that has an assumed initial temperature of 4.5 degree Celsius. The pipe may have no flow through it for long period of time, yet it will not be drained in order that no freezing occurs, the pipe must be kept at a temperature not lower than 0 degree Celsius. The pipe is to be designed for a 30 hour period at the beginning of which the soil surface temperature suddenly drops to – 17 degree Celsius. Workout the minimum earth covering needed above the water pipe so as to prevent the possibility of freezing during 36 hour cold spell. The soil in which the pipe is buried has the following properties Density = 640 kg/m3 Specific heat = 1843J/kg degree Thermal conductivity = 0.345 W/m degree
A counter flow heat exchanger is used to col 2000 kg/hr of oil (c p = 2.5 k J/kg K) from 105 degree Celsius to 30 degree Celsius by the use of water entering at 15 degree Celsius. If the overall heat transfer coefficient is expected to be 1.5 k W/m2 K, find out the water flow rate. Presume that the exit temperature of the water is not to exceed 80 degree Celsius
In a surface condenser, the water flowing through a series of tubes at the rate of 200 kg/hr is heated from 15 degree Celsius to 75 degree Celsius. The steam condenses on the outside surface of tubes at atmospheric pressure and the overall heat transfer coefficient is estimated at 860 k J/m2 hr degree. Find the effectiveness of the heat exchanger. At the condensing pressure, stream has a saturation temperature 0f 100 degree Celsius and the latent heat of vaporization is 2160 k J/kg. Further, the steam is initially just saturated and the condensate leaves the exchanger without sub-cooling i.e. only latent heat of condensing steam is transferred to the water. Take specific heat of water as 4 k J/kg K