Bissoy.com
Doctors Medicines MCQs Q&A

Just before the piston reaches TDC during exhaust stroke, injection of the fuel takes place into the inlet manifold of the cylinder at about 60º crankangle before TDC.

Just before the piston reaches TDC during exhaust stroke, injection of the fuel takes place into the inlet manifold of the cylinder at about 60º crankangle before TDC. Correct Answer True

Yes, just before the piston reaches TDC during exhaust stroke, injection of the fuel takes place into the inlet manifold of the cylinder at about 60º crankangle before TDC.

Related Questions

In IC engine 1. the ideal air capacity of a two-stroke engine is the mass of air required to concurrently fill the total cylinder volume at inlet temperature and exhaust pressure 2. with increase in air-fuel ratio beyond the value for maximum power, there is a fall in power developed and this fall is more with higher values of air-fuel ratio. 3. the volumetric efficiency of the engine depends on the design of intake and exhaust manifold. Which of the above are correct?
Given are the steps to construct an equilateral triangle, when the length of side is given. Using, T-square, set-squares only. Arrange the steps. i. The both 2 lines meet at C. ABC is required triangle ii. With a T-square, draw a line AB with given length iii. With 30o-60o set-squares, draw a line making 60o with AB at A iv. With 30o-60o set-squares, draw a line making 60o with AB at B
Consider the following statements: Combustion chamber is 1. the volume between TDC and BDC during the combustion process 2. the space enclosed between the upper part of the cylinder and the top of the piston during the combustion process 3. the space enclosed between TDC and the top of the piston during the combustion process Which of the above statements is/are CORRECT?
“What is the different between height and radius of solid cylinder?” Which of the following option is sufficient alone to find the answer? A) A solid cylinder is made by melting a solid sphere. The radius of cylinder is 3 times the radius of a circle whose area is 154 sq.m. Height of cylinder is equal to the height of cone whose volume is 2772 cubic meters. B) Area of a rectangle whose longer side is ¾ times the radius of a solid cylinder, is 168 sq.m and, Volume of solid cylinder is 2772 cubic meters and its height is 18 m. C) A metallic cone of radius 15m and height 35m is melted into the solid cylinder of radius equal to the radius of a circle whose area is equal to the area of rectangle whose sides are in the ratio 4 : 3 respectively. D) The curved surface area of the solid cylinder is 3 time the surface area of a sphere of radius 7m and height of cylinder is equal to the height of a metallic cone whose curved surface area is 308 sq.m. 
In a newly developed innovative idea brought up by CSIR in India, gas turbine exhaust gas are being utilized to convert feedwater into steam. Certain data of the experiment are as follows: mass flow rate of exhaust gas = 40 kg/hr, enthalpy of exhaust gas at the time of their exit from gas turbine is 600 kJ/kg, steam turbine output as measured by brake dynamometer = 60 hp-sec, thermal efficiency of steam power plant is 0.25, efficiency of exhaust gas in converting feedwater into steam is taken as 50%. Find the enthalpy of exhaust gas remaining after they generate steam from feedwater?
In an electronic fuel injection system, the ECU calculates the optimum fuel injection volume for the current engine condition based on data from a wide range of sensor, and it injects this volume of fuel into the intake manifold at the optimum timing.
In a diesel engine
1. Fuel injection pump is used
2. Fuel injection pump and carburettor is used
3. Fuel injector is used
4. Neither fuel injection pump nor injector is used
The diameters of a small piston and a large piston of a hydraulic jack are 45 mm and 100 mm respectively.Force of 0.09 kN applied on smaller in size piston. Find load lifted by piston if smaller in size piston is 40 cm above the large piston. The density of fluid is 850 kg/m3
In _____________ cylinder, the piston moves up from BDC to TDC during the exhaust stroke.
If one cylinder of a diesel engine receives more fuel than the others, it is a serious condition for that cylinder and can be checked by 1. Judging the seizure of the piston 2. Checking incomplete combustion in that cylinder 3. Checking cylinder exhaust temperature with a pyrometer Which of the above is/are correct?