Bissoy.com
Doctors Medicines MCQs Q&A

A cone clutch transmits 24kW at 490rpm. The coefficient of friction is 0.2 and allowable intensity of pressure is 0.35N/mm². The semi cone angle is 12⁰. The outer diameter is fixed as 310mm.Assuming uniform wear theory; find the maximum torque which is transmitted.

A cone clutch transmits 24kW at 490rpm. The coefficient of friction is 0.2 and allowable intensity of pressure is 0.35N/mm². The semi cone angle is 12⁰. The outer diameter is fixed as 310mm.Assuming uniform wear theory; find the maximum torque which is transmitted. Correct Answer 467.72N-m

M=Powerx10ᵌx60/2πN.

Related Questions

A cone clutch transmits 24kW at 490rpm. The coefficient of friction is 0.2 and allowable intensity of pressure is 0.35N/mm². The semi cone angle is 12⁰. The outer diameter is fixed as 310mm.Assuming uniform wear theory; calculate force required to engage clutch.
A cone clutch transmits 24kW at 490rpm. The coefficient of friction is 0.2 and allowable intensity of pressure is 0.35N/mm². The semi cone angle is 12⁰. The outer diameter is fixed as 310mm.Assuming uniform wear theory; find the face width of friction lining.
A cone clutch transmits 24kW at 490rpm. The coefficient of friction is 0.2 and allowable intensity of pressure is 0.35N/mm². The semi cone angle is 12⁰. The outer diameter is fixed as 310mm.Assuming uniform wear theory; find the inner diameter.
A plate clutch consists of 1 pair of contacting surfaces. The inner and outer diameter of the friction disk is 100mm and 200mm respectively. The coefficient of friction is 0.2 and permissible intensity of pressure is 1.5N/mm². Assuming uniform wear theory, calculate the torque transmitting capacity of the clutch.
A plate clutch consists of 1 pair of contacting surfaces. The inner and outer diameter of the friction disk is 100mm and 200mm respectively. The coefficient of friction is 0.2 and permissible intensity of pressure is 1.5N/mm². Assuming uniform pressure theory, calculate the torque transmitting capacity of the clutch.
A plate clutch consists of 1 pair of contacting surfaces. The inner and outer diameter of the friction disk is 100mm and 200mm respectively. The coefficient of friction is 0.2 and permissible intensity of pressure is 1.5N/mm². Assuming uniform wear theory, calculate the operating force in the clutch.
A plate clutch consists of 1 pair of contacting surfaces. The inner and outer diameter of the friction disk is 100mm and 200mm respectively. The coefficient of friction is 0.2 and permissible intensity of pressure is 1.5N/mm². Assuming uniform wear theory, calculate the power transmitting capacity of the clutch at 80rad/s.
In the case of the design of friction clutches, the uniform rate of wear theory is used over uniform pressure. The reasons may be the following: 1. It gives lower frictional torque. 2. It gives higher frictional torque. 3. The intensity of pressure is maximum at the inner radius and minimum at the outer radius of the friction or contact surfaces. 4. This concept is prevalent for running and old clutches. Which of the above reasons is correct?
A multiple disc clutch has five plates having four pairs of active friction surfaces. If the intensity of pressure is not to exceed 0.127 N/mm2, find the power transmitted at 500 r.p.m. The outer and inner radii of friction surfaces are 125 mm and 75 mm respectively. Assume uniform wear and take coefficient of friction = 0.3.
Consider the following statements regarding clutches 1. Dry clutch has higher coefficient of friction compared to wet clutch 2. The torque capacity of wet clutch is high compared to dry clutch. 3. The engagement in a dry clutch is smoother than in case of wet clutch. Which of the above statements is/are correct ?