Bissoy.com
Doctors Medicines MCQs Q&A

A machine vice whose length of the handle is 150mm and the coefficient of friction for thread and collar are 0.15 and 0.17 respectively has a force applied at handle of 125N. Also the outer and inner diameters of collar are 55mm and 45mm respectively. Find the clamping force W if nominal diameter=22mm and pitch=5mm.

A machine vice whose length of the handle is 150mm and the coefficient of friction for thread and collar are 0.15 and 0.17 respectively has a force applied at handle of 125N. Also the outer and inner diameters of collar are 55mm and 45mm respectively. Find the clamping force W if nominal diameter=22mm and pitch=5mm. Correct Answer 2868.73N

Net torque=M₁+M₂ or 125 x 150=2.286W + 4.25W or W=2868.73N.

Related Questions

A machine vice whose length of the handle is 150mm and the coefficient of friction for thread and collar are 0.15 and 0.17 respectively has a force applied at handle of 125N. Also the outer and inner diameters of collar are 55mm and 45mm respectively. Find the collar torque in terms of clamping force W assuming uniform wear theory if nominal diameter=22mm and pitch=5mm.
A machine vice whose length of the handle is 150mm and the coefficient of friction for thread and collar are 0.15 and 0.17 respectively has a force applied at handle of 125N. Also the outer and inner diameters of collar are 55mm and 45mm respectively. Find the screw torque in terms of clamping force W if nominal diameter=22mm and pitch=5mm.
A machine vice whose length of the handle is 150mm and the coefficient of friction for thread and collar are 0.15 and 0.17 respectively has a force applied at handle of 125N. Also the outer and inner diameters of collar are 55mm and 45mm respectively. Find the overall efficiency if nominal diameter=22mm and pitch=5mm.
Which of the following is NOT true about Frictional force? A. Friction is the force which opposes the relative motion of two surfaces in contact. B. The force of friction that acts when a body is moving (sliding) on a surface is called sliding friction. C. Friction in machines wastes energy and also causes wear and tear. D. Rolling friction is much more than sliding friction, the use of ball bearings in a machine considerably reduces friction.
What is the collar friction torque if outer and inner diameters are 100mm and 65mm respectively. Coefficient of friction is 0.15 and the load acting is of 15kN. Consider uniform wear theory.
Find number of contacting surfaces for a multi disk clutch plate transmitting torque of 10N-m and inner and outer diameters of friction lining are 70mm and 100mm respectively. The operating force is of magnitude 305N and coefficient of friction is 0.2.
A high pressure cylinder consists of a steel tube with inner and outer diameters 30 and 60mm respectively. It is jacketed by an outer steel tube, having an outer diameter of 90mm. Maximum principal stress induced is 80N/mm². Calculate the radial stress due to shrink shift in inner tube. b) -3.04 c) -3.04 d) +3.04
A high pressure cylinder consists of a steel tube with inner and outer diameters 30 and 60mm respectively. It is jacketed by an outer steel tube, having an outer diameter of 90mm. Maximum principal stress induced is 80N/mm². Calculate the tangential stress due to shrink shift in inner tube. b) -3.04 c) -3.04 d) +3.04
User level threads are threads that are visible to the programmer and are unknown to the kernel. The operating system kernel supports and manages kernel level threads. Three different types of models relate user and kernel level threads. Which of the following statements is/are true ? (a) (i) The Many - to - one model maps many user threads to one kernel thread (ii) The one - to - one model maps one user thread to one kernel thread (iii) The many - to - many model maps many user threads to smaller or equal kernel threads (b) (i) Many - to - one model maps many kernel threads to one user thread (ii) One - to - one model maps one kernel thread to one user thread (iii) Many - to- many model maps many kernel threads to smaller or equal user threads
Which of the following statements regarding laws governing the friction between dry surfaces are correct? 1. The friction force is dependent on the velocity of sliding.  2. The friction force is directly proportional to the normal force. 3. The friction force is dependent on the materials of the contact surfaces. 4. The Friction force is independent of the area of contact surfaces.