Bissoy.com
Doctors Medicines MCQs Q&A

For an elliptical hole on a flat plate, if width of the hole in direction of the load decrease, Stress Concentration Factor will______

For an elliptical hole on a flat plate, if width of the hole in direction of the load decrease, Stress Concentration Factor will______ Correct Answer Increase

K=1+2 x (semi major axis/semi minor axis. Hence K is inversely proportional to the semi minor axis.

Related Questions

A plate with an elliptical hole in the centre, with semi-major axis (a) perpendicular to the direction of loading and semi-minor axis (b) along the direction of loading, is subjected to a pull P. The maximum stress induced at the edge of the hole is equal to (where $$\sigma $$ = Stress for a plate with no hole i.e. nominal stress)
A flat plate 30mm wide and “t”mm wide is subjected to a tensile force of 5kN. The plate has a circular hole of diameter 15mm with the centre coinciding with the diagonal intersection point of the rectangle. If stress concentration factor=2.16, find the thickness of the plate if maximum allowable tensile stress is 80N/mm².
Which one of the following sets is incorrect to show the inter-relationships among price elasticity coefficient, change in price and change in total revenue ? Price elasticity coefficient Change in price Change in Total Revenue 1) Zero Increase Decrease Increase Decrease (2) Less than 1 Increase Decrease Decrease Increase (3) Equal to 1 Increase Decrease No change No change (4) More than 1 Increase Decrease Decrease Increase  
Six flats A, B, C, D, E and F are located in two rows of three flats each. The flats in both the rows face each other. Flat D is diagonally opposite to flat C. Flat E is opposite to flat F, which is north facing. Flat C is 2nd to the left of A and both of flats are south facing. Which of the following flats is facing flat B?
A steel plate is subjected to tension. The tensile force is applied over a width 'a' whereas the gross width of the plate is 'b'. The dispersion of the force from the point of application is at about 30° with the axis and extends to a maximum width of 12 times the thickness t of the plate. The effective width which comes into action will be
A stream of air at 100 kPa pressure and 300 K is flowing on the top surface of a thin flat sheet of solid naphthalene of length 0.2 m with a velocity of 20 m/sec. The other data are: Mass diffusivity of naphthalene vapor in air = 6 * 10 –6 m2/sec Kinematic viscosity of air = 1.5 * 10 –5 m2.sc Concentration of naphthalene at the air-solid naphthalene interface = 1 * 10 – 5 kmol/m3 Calculate the overage mass transfer coefficient over the flat plate. Note: For heat transfer over a flat plate, convective heat transfer coefficient for laminar flow can be calculated by the equation. Nu = 0.664 ReL1/2 Pr1/3 you may use analogy between mass and heat transfer.
The design stress, which is more than the damaging stress, is the least unit stress that will render a member unfit for service before the end of its normal life. The design stress factor or factor of safety indicates the margin between design stress and the __________ stress.
In Sanjay Cafe, the charges for Maharashtrian meal plate is Rs. 45 and charges for South Indian meal plate is Rs. 60. In a particular month, 40 Maharashtrian meal plate were served while number of South Indian meal plate served was 65, then what is the ratio of total charges collected for Maharashtrian meal plate and total charges collected for South Indian meal plate?
Rinki has three plates of Jalebies: Plate A, Plate B and Plate C. Plate A has only one Jalebi, Plate B has five Jalebies and Plate C has three Jalebies. She wants to put equal numbers of Jalebies in all the plates. Which of the following statement is true?
Examine the following statements :
i) Factor of safety for steel should be based on its yield stress,
ii) Factor of safety for steel should be based on its ultimate stress,
iii) Factor of safety for concrete should be based on its yield stress,
iv) Factor of safety for concrete should be based on its ultimate stress.
The correct statements are