Bissoy.com
Doctors Medicines MCQs Q&A

Related Questions

A gear train consist of spur gear as shown. Gear A receives 4kW of power at 750rpm through its shaft and rotates in CW direction. A gear train consist of spur gear as shown. Gear A receives 4kW of power at 750rpm through its shaft and rotates in CW direction. Calculate the torque on the gear C if number of teeth on gear A, B and C are 40, 70 and 30.
A planetary gear train is shown in the figure. Number of teeth on the sun gear A, planet gear B and fixed ring gear D are given by 30, 70 and 140 respectively. Module is taken as 5mm. A pair of spur gears consist of 25 teeth pinion meshing with a 115 teeth gear. The module is 5mm. Calculate the gear ratio.
Following is the data for transmission system of a Gear box reduction ratios.
1st gear - 4.3 : 1
2nd gear - 3.00 : 1
3rd gear - 2.71 : 1
4th gear - 1 : 1
Final drive reduction is 5.0 : 1
The overall reduction when the vehicle is driven in 2nd gear is
Consider two shafts connected with two gears as per the following options: 1. One on each shaft 2. Through an intermediate gear mounted on an intermediate shaft, and every shaft having one gear only 3. Through an intermediate gear mounted on an intermediate shaft, with the intermediate shaft having two gears, whereas the other shafts have one gear each Which of the above represent(s) a simple gear train?
Which of the following statements are correct for mating gears with involute profiles? 1. The pressure angle, from the start of the engagement to the end of the engagement, remains constant. 2. The pressure angle is maximum at the beginning of the engagement, reduces to zero at pitch point, starts decreasing and again becomes maximum at the end of the engagement. 3. The face and flank of the teeth are generated by a single curve and the normal to this curve at any point is tangent to the base circle of the gear. 4. The centre distance for a pair of mating gears can be varied within limits without altering the velocity ratio. Select the correct answer using the code given below.
Which of the following statements are correct for mating gears with involute profiles? (i) The pressure angle, from the start of the engagement to the end of the engagement, remains constant. (ii) The pressure angle is maximum at the beginning of the engagement, reduces to zero at pitch point, starts decreasing and again becomes maximum at the end of the engagement. (iii) The face and flank of the teeth are generated by a single curve and the normal to this curve at any point is tangent to the base circle of the gear. (iv) The centre distance for a pair of mating gears can be varied within limits without altering the velocity ratio. Select the correct answer using the code given below.
A gear train consist of spur gear as shown. Gear A receives 4kW of power at 750rpm through its shaft and rotates in CW direction. Calculate the tangential gear tooth force. Module of the gear is 5mm.
A planetary gear train is shown in the figure. Number of teeth on the sun gear A, planet gear B and fixed ring gear D are given by 30, 70 and 140 respectively. Module is taken as 5mm. Calculate the tangential component of gear tooth force.
Some small cubes of same height 7 cm but variable length and width are put inside a large cuboid of height 21 cm. Length and width of cuboid is 32 cm and 24 cm, respectively. Small cubes are put such that cubes at the bottom most layer is of similar base area; second layer contains all the cubes of similar base area and third layer have all the cubes of similar base area. Which of the following statement(s) given below is / are TRUE? A: If side of each small cubes at bottom most layer is 8 cm, then maximum number of small cubes that can be put at bottom most layer is 12. B: If maximum of 48 cubes can be put at second layer, then side of each cube at second layer is 6 cm. C: If side of each small cubes at third layer is 1.6 cm, then maximum number of small cubes that can be put at third layer is 300.
The accompanying image shows a large cube made of dark and white small sugar cubes. Small cubes of the diagonally arranged row of the bottom surface of the large cube, small cubes of the row with one face on the right-hand surface of the large cube, small cubes of the row with one face on the front surface of the large cube, and small cubes of the column with one face on the top of large cube surface are all dark. Select the number of small white cubes of the large cube.