Bissoy.com
Doctors Medicines MCQs Q&A

Related Questions

Which of the following forces are measured directly by strain gauges or force dynamometers during metal cutting? 1. Force exerted by the tool on the chip acting normally to the tool face 2. Horizontal cutting force exerted by the tool on the workpiece 3. Frictional resistance of the tool against the chip flow acting along the tool face 4. Vertical force which helps in holding the tool in position Select the correct answer using the codes given below.
What is the distance covered by boat N upstream in 5 hours? Which of the following option is sufficient alone to find the answer? A) Boat M is travelling downstream with 20% more downstream speed of boat N. Speed of boat M in still water is 10% more than the speed of boat N in still water. B) Boat M and Boat N are travelling downstream with speed 33 km/hr and 40 km/hr respectively and speed of boat M is still water is 2 times the speed of stream. C) Speed of boat M in still water is 6 km/hr less then speed of boat N in still water and speed of stream is 10 km/hr. D) Speed of stream is ½ times the speed of boat N in still water and downstream speed of boat M is 44 km/hr. E) Speed of stream is 10 km/hr and ratio of upstream speed of boat M and boat N is 3 : 2 respectively.
Given below are three quantities named A, B and C. Based on the given information; you have to determine the relationship between the two quantities. You should use the given data and your knowledge of Mathematics to choose between the possible answers. The options represent the relations between these three quantities A) > B) < C) = D) ≤ E) ≥ Two pipes P and Q can fill an empty tank in 20 minutes and 30 minutes respectively. Quantity A: If both pipes are opened simultaneously, then after what certain time P should be closed so that further time after which the tank is filled in 15 minutes? Quantity B: If both are opened and P is closed after 8 minutes, how much further time would it take for Q to fill the bucket? Quantity C: Pipe A and B can fill a tank in 15 minutes and 10 minutes respectively. Pipe C can empty the tank in 5 minutes. Pipe A and B are opened simultaneously and after the 4-minute pipe, C is also opened. In what time the tank will be emptied?
Flank wear occurs mainly on the 1. Nose part of the cutting tool 2. Front relief face and side relief face of the cutting tool 3. Face of the cutting tool at the shortest distance from the cutting edge Which of the above is/are correct?
Study the two cases and answer in terms of relation between the two cases Case 1: The average speed of the bike is \(3\frac{3}{4}\) times the average speed of the bus. A car covers 720 km in 10 hours. How much distance (in km) will a bike cover in 50 minutes if the speed of the bus is half of the speed of the car? Case 2: The average speed of bike is \(1\frac{2}{5}\) times the average speed of the car. A bus covers 441 km in 7 hours. How much distance (in km) will a bike cover in 45 minutes if the speed of the car is twice the speed of the bus?
Consider the following statements: 1. HSS tools wear very rapidly, whereas in cemented carbide tools, even though hardness is retained, crater wear can occur due to solid-state diffusion. 2. Cutting tools made of Super-HSS, also known as cobalt-based HSS, are made by adding 2% to 15% of cobalt which increases the cutting efficiency at heavier cuts by increasing the hot hardness and wear resistance. 3. Tools failure due to excessive stress can be minimized by providing small or negative rake angles on brittle tool materials, protecting tool tip by providing large side-cutting edge angles, and honing a narrow chamfer along the cutting edge. Which of the above statements are correct?
5 taps are connected to a tank among which 3 taps (A, B and C) are inlet taps and 2 taps (P and Q) are outlet taps. A, B and C can fill the tank in 24 minutes, 30 minutes and 36 minutes respectively while taps P and Q can empty the tanks in 15 minutes and 45 minutes respectively. If tap B is opened after 5 minutes and tap P is opened 5 minutes after tap B, find the time taken to fill the tank completely.
Each of the question below consists of a question and three statements number I, II and III given below it. You have to decide whether the data provided in the statement are sufficient to answer the question. If the bus is travelling from Surat to Ahmadabad and a car is travelling from Ahmadabad to Surat, then what is the distance between Surat and Ahmadabad? I. The speed of a car is 40% less than the speed of bus. Bus started at 9 am and car started at 10 am and they meet at 3 pm of the same day. II. After travelling for 1 hour, because of traffic average speed of bus is decreased by 20% and covers distance between Surat to Ahmadabad in 11 hours. Original speed of car is 20% less than original speed of bus and before crossing bus it covered 200 km if starts 1 hour later than bus. After crossing car, bus covers remaining distance in 5 hours. III. Speed of bus is 10 km/hr more than the speed of car and before crossing car ratio of distances covered bus and car in same time was 5 : 4. Time taken by car to cover the distance between Ahmadabad and Surat is 2 hours 15 minutes more than time taken by bus to cover the same distance.
The relation between the tool life (T) in minutes and cutting speed (V) in m/min is (where n = An exponent, which depends upon the tool and workpiece, and C = A constant)
The relation between the tool life (T) in minutes and cutting speed (V) in m/min is (where n = An exponent, which depends upon the tool and workpiece and C = A constant)