A cast iron T section beam is subjected to pure bending. For maximum compressive stress to be 3 times the maximum tensile stress, centre of gravity of the section from flange side is ____________

A cast iron T section beam is subjected to pure bending. For maximum compressive stress to be 3 times the maximum tensile stress, centre of gravity of the section from flange side is ____________ Correct Answer H/4

H/4 when the applied moment is sagging. Otherwise, I.e. if the applied moment is hogging it is H/4. as in the options both are not given means we have to take hogging.
Bissoy MCQ

Related Questions

Simplify the value of $$\frac{{{\text{0}}{\text{.9}} \times {\text{0}}{\text{.9}} \times {\text{0}}{\text{.9 + 0}}{\text{.2}} \times {\text{0}}{\text{.2}} \times {\text{0}}{\text{.2 + 0}}{\text{.3}} \times {\text{0}}{\text{.3}} \times {\text{0}}{\text{.3}} - {\text{3}} \times 0.9 \times {\text{0}}{\text{.2}} \times {\text{0}}{\text{.3}}}}{{{\text{0}}{\text{.9}} \times {\text{0}}{\text{.9 + 0}}{\text{.2}} \times {\text{0}}{\text{.2 + 0}}{\text{.3}} \times {\text{0}}{\text{.3}} - 0.9 \times {\text{0}}{\text{.2}} - {\text{0}}{\text{.2}} \times {\text{0}}{\text{.3}} - 0.3 \times 0.9}} = ?$$
$$\frac{{38 \times 38 \times 38 + 34 \times 34 \times 34 + 28 \times 28 \times 28 - 38 \times 34 \times 84}}{{38 \times 38 + 34 \times 34 + 28 \times 28 - 38 \times 34 - 34 \times 28 - 38 \times 28}}$$            is equal to = ?
An axial residual compressive stress due to a manufacturing process is present on the outer surface of a rotating shaft subjected to bending. Under a given bending load, the fatigue of the shaft in the presence of the residual compressive stress is ____________
If any cross section is subjected to direct tensile stress and bending stress, then find the dimension of cross section. Given length & breadth are t and 2t respectively. F=25kN acts on the top fibre of the cross section, M=F x t . Also maximum allowable tensile stress =100N/mm².
Compared to mild steel, cast iron has
(i) High compressive strength
(ii) High tensile strength
(iii) Low compressive strength
(iv) Low tensile strength
A body is subjected to a tensile stress of 1200 MPa on one plane and another tensile stress of 600 MPa on a plane at right angles to the former. It is also subjected to a shear stress of 400 MPa on the same planes. The maximum normal stress will be
A body is subjected to a tensile stress of 1200 MPa on one plane and another tensile stress of 600 MPa on a plane at right angles to the former. It is also subjected to a shear stress of 400 MPa on the same planes. The maximum shear stress will be
A body is subjected to a tensile stress of 1200 MPa on one plane and another tensile stress of 600 MPa on a plane at right angles to the former. It is also subjected to a shear stress of 400 MPa on the same planes. The minimum normal stress will be
Out of the total production of iron from hematite, an ore of Iron, 20% of the ore gets wasted, and out of the remaining iron, only 25% is pure iron. If the pure iron obtained in a year from a mine of hematite was 80,000 kg, then the quantity of hematite mined from that mine in the year is
Tina observed the following when she tested the specific gravity of milk to check for adulteration- the specific gravity was lesser than that of pure milk. She complained to the milk vendor and the next day checked the specific gravity again. This time it came in the range of the desired specific gravity. Can we be assured that this is pure unadulterated milk?