Bissoy.com
Doctors Medicines MCQs Q&A

________________ is an air operated drill which can easily be carried from one place to the other.

________________ is an air operated drill which can easily be carried from one place to the other. Correct Answer Jack hammer

Jack hammer is also known as a Sinker as it is mainly used to drill vertical holes. The compressed air moves the Piston and the hammering effect is transferred to the bit through the drill Steel. In place of air, water may be used to remove the cuttings.

Related Questions

At an Electronic Data processing unit, five out of the eight program sets P,Q,R,S,T,U,V and W are to be operated daily. On any one day, except for the first day of a month, only three of the program sets must be the ones that were operated on the previous day. The program operating must also satisfy the following conditions: 1. If program P is to be operated on a day, V can’t be operated on that day. 2. If Q is to be operated on a day, T must be one of the programs to be operated after Q. 3. If R is to be operated on a day, V must be one of the programs to be operated after R. 4. The last program to be operated on any day must be either S or U. If the program sets R and W are to be operated on the first day, which of the following could be the other program on that day?
Five friends went for a trip where each carried a certain number of apples with them. The number of apples carried by C was 1 less than that by D, which was 5 more than the number of apples carried by E. The total number of apples carried by A and B both was equal to the average number of apples carried by C, D and E. If D carried more apples than B and they together carried 14 apples, which of the following is a possible value of the apples carried by A?
Which of the following are percussion drills? (i) Shot drill (ii) Diamond drill (iii) Wagon drill (iv) Churn drill
Which of the following are percussion drills?
(i) Shot drill
(ii) Diamond drill
(iii) Wagon drill
(iv) Churn drill
Pipes P and Q fill a cistern in 12 minutes when operated together, Q and R fill it in 20 minutes when operated together and P and R fill it in 15 minutes when operated together. In how many minutes can all 3 pipes fill the cistern if operated together?
In the following question, sentences of a paragraph have been jumbled and labelled as A, B, C and D. You are required to rearrange the jumbled sentences of the paragraph and mark your response accordingly by selecting the correct option. A: Air conditioning is the process of removing heat and moisture from the interior of an occupied space to improve the comfort of occupants. Air conditioning can be used in both domestic and commercial environments.  B: Electric refrigerant-based AC units range from small units that can cool a small bedroom, which can be carried by a single adult, to massive units installed on the roof of office towers that can cool an entire building. C: Air conditioners often use a fan to distribute the conditioned air to an enclosed space such as a building or a car to improve thermal comfort and indoor air quality.  D: This process is most commonly used to achieve a more comfortable interior environment, typically for humans and other animals.
In a six-digit number, the digit of thousands place is 4. The digit at ten's place is double that of digit at thousand's place and digit at hundreds places is half of the digit at thousand’s place. The digit at unit's place is half of the digit at hundred's place. Digit at Ten thousand's place is sum of the digits at thousands and hundreds place and digit at lakh's place is half the digit at ten thousands place. What will be the number?
If l=length of travel of the drill in mm, n=rpm of the drill, s= feed per revolution of the drill in mm. Then machining time can be given as_____
Distance between the table and drill is_____ in pillar drill machine as compare to table top drill machine.
If t=2minute, n=2rpm and s=5 mm. Then find the value of l. t=machining time in minute, l=length of travel of the drill in mm, n= rpm of the drill and s=feed per revolution of the drill in mm.