Bissoy.com
Doctors Medicines MCQs Q&A

Which type of fall is suitable for 60 cumecs discharge and 1.5 m drop?

Which type of fall is suitable for 60 cumecs discharge and 1.5 m drop? Correct Answer Straight Glacis Fall

In this type of modern fall, a straight glacis is provided after the raised crest. The hydraulic jump is made to happen on this glacis causing sufficient energy dissipation. If not flumed this fall gives good performance. This fall is suitable for 60 cumecs discharge and 1.5 m drop.

Related Questions

Two centrifugal pumps P and R are available for use in a pipe flow system and their head-discharge characteristics are as follows. Pump P Pump R Discharge (cumecs) Head (m) Discharge (cumecs) Head (m) 0 40 0 45 0.12 35 0.14 40 0.2 28 0.24 35 0.3 18 0.3 28   The following statements (S1, S2, and S3) pertain to the head and discharge values during actual operation. Neglect losses in the system. Which of the following statements are correct? S1: When the two pumps P and R are connected in parallel, the discharge is 0.36 cumecs corresponding to a head of 35 m. S2: When the two pumps P and R are connected in parallel, the discharge is 0.36 cumecs corresponding to a head of 70 m. S3: When the two pumps P and R are connected in series, the discharge is 0.3 cumecs corresponding to a head of 46 m.
The following question, there are three statements I, II and III. Read the question carefully and mark your answer according to which statements(s) is/are sufficient to the answer the question. What proportion of liquid of type C is there in the tank of capacity 60 liters after 2 minutes if the tank is initially empty? Statement I: Three pipes P, Q, R fill the tank in 15 minutes, 12 minutes and 10 minutes respectively Statement II: When the tank was empty all the three pipes are opened and they discharge three different types of liquid Statement III: Pipe P discharge type A liquid, pipe Q discharge type B liquid and Pipe R discharge type C liquid
Calculate the depth of cut-off for scour holes for an irrigation channel of F.S.Q equal to 354 cumecs and H.F.Q of natural drainage equal to 600 cumecs. Assume the value of friction factor as 1.
Consider the following statements. I. Syphon falls are commonly used where high levelled small drains do out-fall into a low levelled bigger drain. II. The D/s well is necessary in case of falls greater than 1.8 m and for discharges greater than 0.29 cumecs. III. The design discharge is determined based on the fact that V-notch is used. Which of the following statement is correct?
Name the system, where water falls drop by drop just at the position of roots and water is delivered at or near the root zone of plants, drop by drop.
Consider the following statements. I. Possibility of combining some other structure with a fall eg. regulator, road bridge etc. II. Cutting and filling are required below and above the fall should not be necessarily equal. III. The command should not be reduced due to the lowering of F.S.L and the fall may be located below the outlets. Which of the following statement is correct for site selection of a fall?
Consider the following statements and choose the correct answer:
1. A direct proportionality exists between vapour pressure and the concentration of water vapour in the atmosphere
2. Relative humidity is an expression of the ratio of the actual vapour pressure of the atmosphere when saturated at the same temperature
3. A rise or fall in temperature with no change in vapour pressure will cause a drop or rise, respectively, in relative humidity
4. A rise or fall in vapour pressure with no change in temperature will be accompanied by a rise or fall, respectively, in relative humidity
Design a lined canal carrying a discharge of 20 cumecs. The slope is 1 in 7000. Assume suitable values for side slopes and lining.
When a ball is allowed to fall, the time it takes to fall any distance varies as the square root of the distance and it takes 4 seconds to fall 78.40 m. How long would it take to fall 122.50 m?
Good 'Y' is the substitute for good 'X' if
1. A fall in the price of good X leads to the fall in the marginal utility of good Y.
2. A fall in the price of good X leads to the fall in the quantity purchased of good Y. Select the correct answer