Bissoy.com
Doctors Medicines MCQs Q&A

In NGH-SSR Damping Scheme the series resistor has to be designed to limit the rate of current rise and peak capacitor discharge current.

In NGH-SSR Damping Scheme the series resistor has to be designed to limit the rate of current rise and peak capacitor discharge current. Correct Answer True

In NGH-SSR Damping Scheme the series resistor has to be designed to limit the rate of current rise and peak capacitor discharge current. The resistor only consumes power and does not supply power. Also the inductance is accordingly to be designed for getting the desired benefits.

Related Questions

Rithika had Rs 8000. She invested some of it in savings scheme P and the rest ofthe money in savings scheme Q. She invested for 3 years in savings scheme P and for2 years in savings scheme Q. savings scheme P offers SI at a rate of 20% pa whilesavings scheme Q compounded annually at the rate of 30% pa. The interest receivedfrom savings scheme P is 930 more than the interest received from savings scheme Q.If Rs 1500 is debited from the invested amount of savings scheme P then find thedifference between the amount invested by Rithika in savings scheme P & savingsscheme Q.
Which of the following methods are used for producing damping torque in analog instruments? 1) Air friction damping 2) Fluid friction damping 3) Eddy current damping 4) Electromagnetic damping
Two centrifugal pumps P and R are available for use in a pipe flow system and their head-discharge characteristics are as follows. Pump P Pump R Discharge (cumecs) Head (m) Discharge (cumecs) Head (m) 0 40 0 45 0.12 35 0.14 40 0.2 28 0.24 35 0.3 18 0.3 28   The following statements (S1, S2, and S3) pertain to the head and discharge values during actual operation. Neglect losses in the system. Which of the following statements are correct? S1: When the two pumps P and R are connected in parallel, the discharge is 0.36 cumecs corresponding to a head of 35 m. S2: When the two pumps P and R are connected in parallel, the discharge is 0.36 cumecs corresponding to a head of 70 m. S3: When the two pumps P and R are connected in series, the discharge is 0.3 cumecs corresponding to a head of 46 m.
A person invested Rs.2500 more in scheme B than that in scheme A. Scheme A offers 24% simple rate of interest and scheme B offers 20% annual rate of compound interest. If Interest from scheme A after 4 years is Rs.1080 more than that from scheme B after 3 years, then what is the ratio of amount invested in scheme A to that in scheme B?
Consider the following types of damping: 1. Air-friction damping 2.Fluid-friction damping 3.Eddy-current damping PMMC type instruments use which of the above?
A cam should be designed only using uniform rise and fall within half of the cam, the remaining is dwell period, and without any dwell period in between the rise -fall periods and rise and fall periods should be same. The maximum rise in follower is 30 mm. How much the follower will rise when the follower is 120 degrees from its initial position of a cam?
A cam should be designed only using uniform rise and fall within half of the cam, the remaining is dwell period, and without any dwell period in between the rise-fall periods and rise and fall periods should be same. The maximum rise in follower is 45 mm. How much the follower will rise when the follower is 45 degrees from its initial position of a cam?
A cam should be designed only using uniform rise and fall within the second half of cam profile, the first half is dwell period, without any dwell period in between the rise and fall periods and rise and fall periods should be same. The maximum rise in follower is 45 mm. How much the follower will rise when the follower is 120 degrees from its initial position of a cam?
A cam should be designed only using uniform rise and fall within the second half of cam profile, the first half is dwell period, without any dwell period in between the rise and fall periods and rise and fall periods should be same. The maximum rise in follower is 55 mm. How much the follower will rise when the follower is 240 degrees from its initial position of a cam?
A cam should be designed only using uniform rise and fall within first half of cam profile, the remaining is dwell period, and without any dwell period in between the rise-fall periods and rise and fall periods should be same. The maximum rise in follower is 35 mm. How much the follower will rise when the follower is 240 degrees from its initial position of a cam?