Bissoy.com
Doctors Medicines MCQs Q&A

The current reflection coefficient is given by -0.75. Find the voltage reflection coefficient.

The current reflection coefficient is given by -0.75. Find the voltage reflection coefficient. Correct Answer 0.75

The voltage reflection coefficient is the negative of the current reflection coefficient. For a current reflection coefficient of -0.75, the voltage reflection coefficient will be 0.75.

Related Questions

When an electric current coil of a wattmeter is connected to the electric current path R and the voltage coil is connected between the electric current R path and the neutral side of the balanced three phase supply, it shows 10 kW. The line voltage along the phase sequence RYB is 400 V. The current drawn by the current path is 54 A. What is the new reading of the wattmeter if the voltage coil is connected between the lines B and the Y paths, even if the electric current coil is continuously present in the line R?
3 m দুরত্বে অবস্থিত দুটি বিন্দু চার্জের মধ্যে 0.075 N বল কাজ করে। চার্জ দুটির সর্বমোট চার্জের পরিমান 20 μC হলে চার্জ দুটির মান কত?(Two point charges that are at 3m apart experience a force of 0.075 N. If the value of their combined charge is 20 µC, what are the individual values of the charges?)
A soap bubble of d mm diameter is observed inside a bucket of water. If the pressure inside the bubble is 0.075 N/cm2, what will be the value of d? (Take surface tension as 0.075 N/m)
Which of the following statements are correct for an ideal constant voltage source? 1. Its output voltage remains absolutely constant whatever the change in load current. 2. It possesses zero internal resistance so that internal voltage drop in the source is zero. 3. Output voltage is provided by the source would remain constant irrespective of the amount of current drawn from it. 4. Output voltage provided by the source varies with the amount of current drawn from it.
The current reflection coefficient of a line with voltage reflection coefficient of 0.65 is given by
Consider the following statements regarding n-channel JFET: 1. The maximum drain current IDSS occurs when gate-to-source voltage VGS = 0 V and drain-to-source voltage VDS ≥ |VP|. (VP is pinch-off voltage). 2. For gate-to-source voltage VGS less than the pinch-off level, the drain current is 0 A. 3. For all levels of VGS between 0 V and the pinch-off level, the current ID will range between IDSS and 0 A, respectively. which of the above statements are correct ?
What are the steps required in sequence to solve a circuit using superposition theorem? (a) Select any one source and short circuit all other voltage sources. (b) Find out the current or voltage across the required element, due to the source under consideration. (c) Open all current sources, if the internal impedance is not known. If known replace them by their impedances. (d) Add all the individual effects produced by individual sources to obtain the total current in or across the voltage element. Code :
Consider the following statements: 1. The voltage developed across the OFF switches of the half-bridge converter is the maximum dc-link voltage. 2. In the full-bridge converter, the voltage across the primary of the transformer is the dc link voltage. 3. The voltage developed across the OFF switches of the full-bridge converter is half the maximum dc-link voltage. Which of the above statements are correct?
Consider the following statement: a) When resistance is connected to the AC source, the current leads the voltage. b) When resistance is connected to the AC source, the current lags behind the voltage. c) When resistance is connected to the AC source, the current and the voltage are in the same phase. Which of the following statement is correct?
Consider the following statements regarding reciprocity theorem : 1. In any passive linear bilateral network, if the single voltage source Vx, in branch x produces the current response Iy, in branch y, then the removal of the voltage source from branch x and its insertion in branch y will produce the current response iy in branch x. 2. The interchange of an ideal voltage source and an ideal ammeter in any passive, linear, bilateral circuit will not change the ammeter reading. 3. The interchange of an ideal current source and an ideal voltmeter in any passive linear bilateral circuit will change the voltmeter reading. Which of the above statements are correct ?