Bissoy.com
Doctors Medicines MCQs Q&A

In a single phase induction regulator, the voltage boost is maximum when armature mmf and rotor mmf make an angle of ____________

In a single phase induction regulator, the voltage boost is maximum when armature mmf and rotor mmf make an angle of ____________ Correct Answer zero degrees

To obtain a maximum of the voltage in induction regulator, the stator mmf and rotor mmf should be stationary and aligned to each other.

Related Questions

In the following question, sentences of a paragraph have been jumbled and labelled as A, B, C and D. You are required to rearrange the jumbled sentences of the paragraph and mark your response accordingly by selecting the correct option. A: An induction motor can, therefore, be made without electrical connections to the rotor. B: Three-phase squirrel-cage induction motors are widely used as industrial drives because they are self-starting, reliable and economical. C: An induction motor's rotor can be either wound type or squirrel-cage type. D: An induction motor or asynchronous motor is an AC electric motor in which the electric current in the rotor needed to produce torque is obtained by electromagnetic induction from the magnetic field of the stator winding.
In a three phase induction motor of rotor impedance as (0.2+j0.2), rotor current in each phase lags behind the generated emf in that phase to rotor by a power factor angle of _________
A synchronous motor on load draw a current at a leading power factor angle ϕ. If the internal power factor angle which is the phase angle between the excitation emf and the current in the time phasor diagram is ψ. Then the air gap excitation mmf lags the armature mmf by
In an alternator, the armature winding is kept stationary while the field winding is kept rotating for the following reasons: 1. Armature handles very large current and high voltage 2. Armature fabrication, involving deep slots to accommodate large coils, is easy if armature is kept stationary 3. It is easier to cool the stator than the rotor Which of the above reasons are correct?
What is the amplitude of rotating MMF produced as a result of m-phase currents flowing in m-phase windings? (where Fm is maximum MMF in any one phase, when current is maximum in that phase.)
A three-phase cylindrical rotor synchronous generator has a synchronous reactance Xs and a negligible armature resistance. The magnitude of per phase terminal voltage is VA and the magnitude of per phase induced emf is EA. Considering the following two statements, P and Q, P: For any three-phase balanced leading load connected across the terminals of this synchronous generator, VA is always more than EA Q: For any three-phase balanced lagging load connected across the terminals of this synchronous generator, VA is always less than EA Which of the following options is correct?
A balanced 3 – phase induction motor runs at slip s. If ωs is its synchronous speed, what is the relative speed between the stator mmf and rotor mmf ?
The network formed by resistors and capacitors for modifying the rate of change of gain and the phase shift is called a compensating network. Which of the following statements are not correct ? (A) The main purpose of a compensating network is to modify the performance of op-amp ciruit over the desired frequency range (B) There are two types of op-amps : internally compensated and externally compensated (C) 741 C is an externally compensated op-amp while 709 C is internally compensated op-amp (D) The phase lag and phase lead are most commonly used compensating networks in op-amps (E) Phase lag contributes a positive phase angle and phase lead a negative phase angle Choose the most appropriate answer from the options given below : 
In a three phase induction motor, rotor current in each phase lags behind the generated emf in that phase to rotor by a power factor angle of _________
A 10 kW, 400 V, 3-phase, 4-pole, 50 Hz induction motor develops the rated output at rated voltage with its slip rings shorted. The maximum torque is twice the full load torque occurs at the slip of 10% with zero external resistance in the rotor circuit. An external resistance is now tripled in the rotor circuit. Then the slip at which maximum torque occur for the same load torque is?