Bissoy.com
Doctors Medicines MCQs Q&A

Given the shear modulus(G) for aluminum as 2.4e+10 N/m2 and the shear strain is given as 6e-5. What is the value for shear stress?

Given the shear modulus(G) for aluminum as 2.4e+10 N/m2 and the shear strain is given as 6e-5. What is the value for shear stress? Correct Answer 14.4e+5 N/m2

Shear modulus is the ratio of shear stress and shear strain. Therefore, if we simply multiply the shear modulus and shear strain we will obtain the shear stress. Hence the final answer is 2.4e+10 x 6e-5 which gives us 14.4e+5 N/m2 as the final answer.

Related Questions

From an alloy, two specimens are machined and tested separately under tension and compression. The engineering stress-strain curves as well as the true stress-true strain curves for tension and compression are plotted in the same diagram. Identify the correct statements:
P. The engineering stress-strain curves in tension and compression are identical.
Q. The true stress-true strain curve in compression is lower than the true stresstrue strain curve in tension due to Bauschinger effect.
R. The true stress-true strain curve in tension is above the corresponding engineering stress-strain, curve.
S. The true stress-true strain curve in tension and compression are identical.
Tresca or maximum-shear stress criteria assumes that yielding occurs when the maximum shear stress reaches a value of the shear stress in the uniaxial tension test. Assume the principal stress being σ1, σ2, σ3 where σ1 is largest, and σ3 is the smallest principal stresses. Find the value of minimum shear stress to cause yielding, given that yield stress in tension is equal to σo?
The true strain rate is given as ϒ, and conventional strain rate is given as ε. The engineering strain is equal to e. The relationship between conventional strain rate and true strain rate is _______
What is the relationship between engineering stress and true stress? Given that; s = engineering stress, σ = true stress, e = engineering strain, ε = true strain. d) σ = se+1
Which of the following factors are affecting critical shear stresses? 1. Purity of metals reduces the critical shear stress 2. Surface films greatly enhance the critical shear stress 3. Rise in temperature 4. Rate of deformation and the extent of initial deformation also help in raising the critical shear stress
A fluid, in which shear stress is more than the yield value and shear stress is proportional to the rate of shear strain is known as:
Consider a deep-space probe constructed as 1 m diameter polished aluminum sphere. Estimate the equilibrium temperature that the probe reaches if the solar energy received is 300 W/m2. For solar radiation, absorptivity of aluminum is 0.3 and the average emissivity appropriate for aluminum at low temperature is 0.04
Which of the following statements regarding stress related factors is/are true and false?
1. Burnout Stress Syndrome (BOSS) is a debilirating psychological condition brought about by unrelieved work stress.
2. 'Good' and 'bad' stresses are also referred to as 'Distress' and 'Eustress' respectively.
3. It is natural and healthy to maintain optimal level of stress.
4. Rustout Stress Syndrome (ROSS) is indicative of stress overload.
5. Anxiety is a state of emotional tension characterised by Apprehension, fearfulness, and psychic pain.
A wall bracket is attached to the wall by means of 2 identical bolts, one at A and one at B. The force of 20kN acts at a distance of 400mm. Bolt A lies at a distance of 50mm from axis of tilt and bolt B 500mm. Allowable shear stress in the bolts is 100N/mm² and tensile is 40N/mm². Find the radius of Mohr circle which can be made from the shear stress and tensile stress acting on bolts.(Consider bolt under max stress and area of bolt is A)
The strain energy stored in a body due to shear stress, is (where $$\tau $$ = Shear stress, C = Shear modulus and V = Volume of the body)