Bissoy.com
Doctors Medicines MCQs Q&A

Higher input voltage can be measured in low voltage DC voltmeter using

Higher input voltage can be measured in low voltage DC voltmeter using Correct Answer Higher resistance value

Higher resistance values are required to measure relatively higher input voltage. For example, if the range of switch is at x10 position in the low voltage dc voltmeter then, the corresponding resistance value would be 10kΩ. So, it requires a 10v input to get a full scale deflection (if 1v cause full scale deflection in the ammeter with a full scale deflection of 1mA).

Related Questions

A resistance R is measured using the connection shown in the below figure. The current measured is 10 A on ranges 100A and the voltage measured is 125 V on 150 V range. The scales of the ammeter and voltmeter are uniform. The total number of scale divisions of the ammeter is 100 and that of the voltmeter is 150. The scale division can be distinguished. The constructional error of the ammeter is ± 0.3% and that of voltmeter±0.4%. The resistance of the ammeter is 0.25 Ω. The possible error in the measurement of R is?
Consider the following statements regarding electronic voltmeter. 1) The detection of low-level signals is not possible using the electronic voltmeter 2) MOSFET is used at the input of the electronic voltmeter 3) Vacuum tube voltmeters (VTVM) consumes more power as compared to any non-electronic voltmeter. Which of the following is / are incorrect?
How to modify a low voltage DC voltmeter to low voltage ac voltmeter
An average responding rectifier type electronic ac voltmeter has its scale calibrated in terms of the rms value of a sine wave. If a square wave voltage of peak amplitude of 100 V is measured using this voltmeter, what will be the reading indicated by the meter?
Consider the following statements. 1. BJT is a current controlled device whereas IGBT is a voltage-controlled device. 2. BJT and IGBT have low input impedance whereas PMOSFET has higher input impedance. 3. IGBTs are available at higher voltage ratings than PMOSFETs because of increment in ON state voltage drop is less in IGBT. 4. IGBT and PMOSFETs have different substrate structures. The correct statements are
Consider the following statements regarding reciprocity theorem : 1. In any passive linear bilateral network, if the single voltage source Vx, in branch x produces the current response Iy, in branch y, then the removal of the voltage source from branch x and its insertion in branch y will produce the current response iy in branch x. 2. The interchange of an ideal voltage source and an ideal ammeter in any passive, linear, bilateral circuit will not change the ammeter reading. 3. The interchange of an ideal current source and an ideal voltmeter in any passive linear bilateral circuit will change the voltmeter reading. Which of the above statements are correct ?
For an instrumentation amplifier, the following parameters are given (a) High input resistance and low power consumption (b) Low input resistance and low power consumption (c) High CMRR and high slew rate (d) Low CMRR and high slew rate Which of the given parameters are a major requirement for an instrumentation amplifier?
Which Statements is / are correct ? A. An ammeter is connected in series in a circuit and a voltmeter is connected in Parallel. B. An ammeter has a high resistance C. A voltmeter has a low resistance
The input impedance of the permanent magnet moving coil (PMMC) voltmeter is infinite. Assuming that the diode shown in the figure below is ideal, the reading of the voltmeter in Volts is
A word arrangement machine, When given an input line of words, rearranges it in every step following a certain rule. Following is an illustration of an input line of words and various steps of rearrangement.
Input: gone are take enough brought station
Step 1: take gone are enough brought station
Step 2: take are gone enough brought station
Step 3: take are station gone enough brought
Step 4: take are station brought gone enough
And Step 4 is the last step for this input. Now, find out an appropriate step in the following question following the above rule. Question:
Input: car on star quick demand fat
What will be the third step for this input ?