Bissoy.com
Doctors Medicines MCQs Q&A

Determine the output voltage for the non-inverting amplifier input voltage 37µVpp sinewave. Assume that the output is a 741.

Determine the output voltage for the non-inverting amplifier input voltage 37µVpp sinewave. Assume that the output is a 741. Correct Answer 7.4Vpp sinewave

The output voltage for non-inverting amplifier Vo = A*Vin = 200000 * 37µ = 7.4 Vpp sinewave.

Related Questions

Find the output offset voltage of an 741 op-amp; If the gain of the non-inverting amplifier is 8.5 and feedback resistor = 15kΩ? (IB=200nA for 741 op-amp)
A certain noninverting amplifier has Ri of 1 kΩ and Rf of 100 kΩ. The closed-loop voltage gain is
An amplifier without feedback has a voltage gain of 50, input resistance of 1 kΩ & Output resistance of 2.5 kΩ.The input resistance of the current shunt negative feedback amplifier using the above amplifier with a feedback factor of 0.2 is
A system provides output yi(t) when xi(t) is applied. If the system is said to be LTI then which of the following properties must satisfy? (i).If the input is x3 = ax1(t) + bx2(t), then output must be y3(t) = ay1(t) + by2(t) (ii).If the input is x(t – T), then the output must be y (t – T) (iii).If the input is x3 = ax1(t) + bx2(t), then output must be y3(t) = ay1(t) * by2(t) (iv).If the input is x(t – T), then the output must be y(t + T)
In designing with op amps one has to check the limitations on the voltage and frequency ranges of operation of the closed-loop amplifier, imposed by the op-amp finite bandwidth (ft), slew rate (SR), and output saturation (Vo max). Consider the use of an op amp with ftt = 2 MHz, SR = 1 V/µs, and V0 max = 10 V in the design of a non-inverting amplifier with a nominal gain of 10. Assume a sine-wave input with peak amplitude Vi. If Vi = 0.5 V, what is the maximum frequency before the output distorts?
In designing with op amps one has to check the limitations on the voltage and frequency ranges of operation of the closed-loop amplifier, imposed by the op-amp finite bandwidth (ft), slew rate (SR), and output saturation (Vo max). Consider the use of an op amp with ftt = 2 MHz, SR = 1 V/µs, and V0 max = 10 V in the design of a non-inverting amplifier with a nominal gain of 10. Assume a sine-wave input with peak amplitude Vi. If f = 20 kHz, what is the maximum value of Vi before the output distorts?
Find the input and output resistance for the circuit shown. Specification for 741 op-amp : A=400000 ; Ri = 33MΩ; Ro = 60Ω; RF = 11kΩ; R1 = 2kΩ; Supply voltage = ± 15v; Maximum output voltage swing = ± 13v.
Consider a voltage series feedback network, where amplifier gain = 100, feedback factor = 5. For the basic amplifier, input voltage = 4V, input current=2mA. Find the input resistance of the network.
In a certain code language “Subtle way of thinking” is written as “456 123 789 654”, “The optimistic thinking” is written as “963 789 741” “The Hopeful wins” is written as “423 741 159” and “Thinking Different way” is written as “789 984 123”. What is the code for “Different” and “Optimistic” in that code language?
If the output of the sinewave oscillator is Vsinωot, then determine the output of the inverter in the Biphasic oscillator.