Bissoy.com
Doctors Medicines MCQs Q&A

Flicker noise occurs in solid-state components and vacuum tubes.

Flicker noise occurs in solid-state components and vacuum tubes. Correct Answer True

Flicker noise is a form of noise that exhibits an inverse frequency power density curve. It has a pink noise power density spectrum. Since this noise is inversely proportional to the operating frequency, it is called 1/f noise.

Related Questions

A small and medium enterprise imports two components A and B from Taiwan and China respectively and assembles them with other components to form a toy. Components A contributes to 10% of production cost while components B contributes to 20% of production cost. Usually the company sells this toy at 20% above the production cost. Due to increase in the raw material and labour cost in both the countries ,component A became 20% costlier and components B became 40% costlier. Owing to these reasons the company increased its selling price by 15%. Considering that cost of other components does not change. What will be the profit percentage if the toy is sold at the new price?
Below a question is given with one passage and its effects (I) and (II). One of these effects or both or none may be the effect of the statement. Read both the effect and decide which of the following answer choice correctly depicts the relationship between these cause and effect. Passage: In the urban area there exist a lot of industries, commercial places and public places religious places which involve a lot of a  people and working machinery note of sound and when this sound becomes unpleasant it is known as noise. it is one of the reasons why public authorities have divided the city into a number of zones is known as a different noise level. Effects: I        Noise leads to emotional and behavioural stress. A person may feel disturbed in the presence of loud noise such as produced by heating of drums. II       Noise may cause damage to the liver, brain, and heart.  
Which of the following are the basic differences between vibration signature and noise signature? 1. Vibration signature is essentially in the frequency range zero to 100 cps whereas noise signature is in the range 20 cps to 3000 cps. 2. Vibration signature has well-defined peaks whereas the noise signal is smeared. 3. The intensities of noise signatures arc much less than that of vibration signatures. 4. Detection of vibration signature calls for a microphone whereas that of noise can do with a pickup. Select the correct answer using the code given below.
The important design and operating considerations for Extended-Surface Compact Heat Exchangers are: (1) Both fluids may have high or low heat transfer coefficients (2) As the tubes are very narrow (low DH), the fluid used should not be corrosive as effective cleaning of tubes is not possible. (3) The fluid pressure drop calculation is important as a regulatory method to ensure long life of the tubes. (4) Unlike shell and tube type heat exchangers, these are limited when it comes to operating pressure and temperature.
A two pass surface condenser is required to handle the exhaust from a turbine developing 15 MW with specific steam consumption of 5 kg/k W h. The quality of exhaust steam is 0.9, the condenser vacuum is 66 cm of mercury while the bar meter reads 76 cm of mercury. The condenser tubes are 28 mm inside diameter, 4 mm thick and water flows through tubes with a speed of 3 m/s and inlet temperature 20 degree Celsius. All the steam is condensed, the condensate is saturated water and temperature of cooling water at exit is 5 degree Celsius less than the condensate temperature. Assuming that overall coefficient of heat transfer is 4 k W/m2 degree, determine the mass of cooling water circulated
Thermal noise shot noise and transit time noise is part of internal noise in communication.
Atmospheric noise, extraterrestrial noise and man-made noise is part of internal noise in communication.
Antenna noise temperature of a system is 210 K, noise temperature of transmission line is 123 K, loss of a transmission line connecting the antenna to receiver is 1.41 and noise temperature of the receiver cascade is 304 K. then the total system noise temperature is:
In the question below are given two statements followed by three conclusions I, II and III. You have to take the given statements to be true even if they seem to be at variance from commonly known facts. Read all the conclusions and then decide which of the given conclusions logically follows from the given statements disregarding commonly known facts. Statements: No pot is jug. All pots are tubes. Conclusions: I. Some tubes are jugs. II. Some jugs are tubes. III. No jug is tube.
Which of the following are barriers to effective communication? 1. Physical noise 2. Semantic noise 3. Psychological noise 4. Non-semantic noise Choose the correct answer from the options given below.