Bissoy.com
Doctors Medicines MCQs Q&A

The lossless T junction dividers can be can all be modeled as a junction of three transmission lines.

The lossless T junction dividers can be can all be modeled as a junction of three transmission lines. Correct Answer True

A T junction consists of three ports; hence they can be modeled with 3 transmission lines. However, they cannot be both lossless and matched simultaneously.

Related Questions

The statement concern psychrometric chart. 1. Constant relative humidity lines are uphill straight lines to the right 2. Constant wet bulb temperature lines are downhill straight lines to the right. 3. Constant specific volume lines are downhill straight lines to the right. 4. Constant enthalpy lines are coincident with constant wet bulb temperature lines. Which of the statements are correct?
For the realization of lossless T-junction power divider using transmission lines, the characteristic impedance of the transmission line has to be real.
Assertion (A): A p-n junction diode with low junction depth can be used as a solar cell when illuminated by suitable light (wavelength) at the top thin layer above the junction. Reason (R): A p-n junction diode under no condition can be used as a solar cell. It can be used only as a light-emitting diode for optoelectronic applications.
Each question presents a situation and asks you to make a judgement regarding that particular circumstance. Choose an answer based on given information. Three friends are waiting for a train on the railway station. Suddenly, a train passes by and each of them tries to remember the train number of the train written on each of the coaches. The train number was a 5-digit number. All must agree in order to confirm the digit of train number. 1. All three agrees that all the digits of the train number was different. 2. All three agrees that the difference of 3rd and 5th digit from left is equal to the 4th digit from the left. 3. All three agrees that the 1st digit was 1. 4. All three agrees that the 2nd digit was an even prime number. Which of the following would be most likely the train number?
Consider the following statements.
1. Magnetic lines of force are closed curves while electric lines are not.
2. Electric lines of force are closed curves while magnetic lines are not.
3. Both electric and magnetic lines of force are closed curves.
Which of statement(s) given above is/are correct?
Match Old name with the new name. Old Name  New Name I. Allahabad Junction a) Pandit Deen Dayal Upadhyaya Junction II. Manduadih railway station b) Prayagraj Junction III. Mughalsarai junction c) Prayagraj Rambaug Railway station IV. Allahabad City railway station d) Banaras Railway Station Choose the correct code given below:
Sourab hires a car at junction A and drives 16 km towards north. He takes a right turn and drives 30 km to reach a bus stand. He now drives 10 km after taking a left turn to reach a petrol bunk. Finally, he takes a left turn and drives 30 km, and stops at Junction B. How far is junction A with respect to junction B?
A transistor is used in common emitter mode as an amplifier. Then a. The base-emitter junction is forward biased b. The base-emitter junction is reverse biased  c. The input signal is connected in series with the voltage applied to the base-emitter junction  d. The input signal is connected in series with the voltage applied to bias the base-collector junction Which of the following statement is true?
For transistor action (a) Base, emitter, and collector regions should have similar size and doping concentrations. (b) The base region must be very thin and lightly doped. (c) The emitter-base junction is forward biased and the base-collector junction is reverse biased. (d) Both the emitter-base junction as well as the base-collector junction are forward biased. Which one of the following pairs of statements is correct?
Which of the following conditions must be satisfied for a transistor to be in saturation? 1. Its collector to base junction should be under forward bias 2. Its collector to base junction should be under reverse bias 3. Its emitter to base junction should be under reverse bias 4. Its emitter to base junction should be under forward bias Which of the above conditions are correct?