Bissoy.com
Doctors Medicines MCQs Q&A

Control system are normally designed to be:

Control system are normally designed to be: Correct Answer Under damped

Practically there are some non-linearity present in the system as friction but in mathematical models these are considered by considering high gain and lower damping. Due to this reason generally control system, are normally designed to be under damped.

Related Questions

Which of the following is/are the advantages of using a control chart for inspection? (i) A control chart indicates whether the process is in control or out of control. (ii) A control chart determines process variability. (iii) A control chart ensures product quality. (iv) Scrap or percentage reduction can be reduced by taking the necessary actions in time against the warnings indicated by control charts. (v) Control charts build up the reputation of the organization through customer’s satisfaction. (vi) The control chart can detect the unusual variations taking place in a process.
Based on the given para, answer the following question. Sensitivity considerations often are important in the design of Control Systems. Because all physical elements have properties that change with environment and age, we cannot always consider the parameters of the Control System to be completely stationary over the entire operating life of the system. For instance, the winding resistance of an electric motor changes as the temperature of the motor rises during operation. Control systems with electric components may not operate normally when first turned on because of the still-changing system parameters during warmup. This phenomenon is sometimes called “morning sickness”. Most duplicating machines have a warmup period during which time operation is blocked out when first turn on. A good Control System should be: (a) Very sensitive to parameter variations (b) Insensitive to parameter variations (c) Insensitive to input commands (d) Sensitive to input commands Which of the above are correct?
In counterfort type retaining wallsi) the vertical slab is designed as a continuous slabii) the heel slab is designed as a continuous slabiii) the vertical slab is designed as a cantileveriv) the heel slab is designed as a cantileverThe correct answer is
In counterfort type retaining walls
i) the vertical slab is designed as a continuous slab
ii) the heel slab is designed as a continuous slab
iii) the vertical slab is designed as a cantilever
iv) the heel slab is designed as a cantilever
The correct answer is
Consider a control unit generating the control signals. These control signals are divided into five mutually exclusive groups as shown below: Groups  G1  G1  G1  G1  G1 Control  Signals   3  7  10  12  2 How many bits are saved using the Vertical Micro-programmed instead of Horizontal Micro-programmed control unit?
Examine the following statements about span of control and identify the ones which are true?
1. More task complexity requires narrower span of control.
2. Routine tasks can have greater span of control than exceptional tasks.
3. When tasks are dissimilar, then span of control can be larger.
4. Spans of control are generally narrower at the top and broader at the bottom of the hierarchy.
HACCP is a preventive programme for hygienic control and food safety. Arrange the following steps of the HACCP system intheir correct sequence.
1. Identifying critical control points.
2. Monitoring each critical control point.
3. Developing criteria for control and prevention.
4. Identification and assessment of hazards.
5. Taking immediate corrective action.
What are the conditions to be satisfied by a voltage source for using it in switching regulator. i. It must supply the required output power and the losses associated with the switching regulator ii. It must be large enough to supply sufficient dynamic range line and load variations iii. It must be sufficient high to meet the minimum requirement of the regulator system to be designed iv. It may be required to store energy for a specified amount of time during power failure especially if the system is designed for a computer power supply.
The input signals to control systems are not known fully ahead of time, the characteristics of control system which suddenly strain a control system are:
Consider three software items: Program-X, Control Flow Diagram of Program-Y and Control Flow Diagram of Program-Z as shown below Program-X: Control Flow Diagram of Program-Y sumcal (int maxint, int value) {       int result=0, i=0;       if (value <0)       {           Value = -value;       }       while ( (i