Bissoy.com
Doctors Medicines MCQs Q&A

In the circuit shown below, if current is defined as the response signal of the circuit, then determine the transfer function.

In the circuit shown below, if current is defined as the response signal of the circuit, then determine the transfer function. Correct Answer H(s)=SC/(S2 LC+RCS+1)

If the current is defined as the response signal of the circuit, then the transfer function H (s) = I/V = 1/(R+sL+1/sC) = sC/(s2Lc+RCs+1) where I corresponds to the output Y(s) and V corresponds to the input X(s).

Related Questions

Below are given two sets, Set - I which gives modalities of operant conditioning and Set - II which provides the types of reinforcement, the types of responses (responses made or withheld) and the presence or absence of cue. Match the two sets and indicate your answer by choosing from the code : Set - I (Modalities of operant conditioning procedures) Set – II           (Conditions and contexts) (a) Reward training (i) Positive reinforcement, response made, with cue present (b) Escape training (ii) Positive reinforcement, response withheld with cue absent (c) Discriminated omission training   (iii) Positive reinforcement, response made with cue absent (d) Active avoidance   (iv) Negative reinforcement, response made with training (e) Punishment training (v) Positive reinforcement, response withheld with cue present   (vi) Negative reinforcement, response withheld with cue absent  
Consider the system shown in the figure below. The transfer function $$\frac{{Y\left( z \right)}}{{X\left( z \right)}}$$  of the system is
Signal Processing mcq question image
The impulse response and the excitation function of a linear time invariant causal system are shown in figure (a) and (b) respectively. The output of the system at t = 2 sec is equal to
Signal Processing mcq question image
The function x(t) is shown in the figure. Even and odd parts of a unit-step function u(t) are respectively,
Signal Processing mcq question image
In the circuit shown below, if voltage across the capacitor is defined as the output signal of the circuit, then the transfer function is?
Consider the following solution to the producer-consumer synchronization problem. The shared buffer size is ?. Three semaphores empty, full and mutex are defined with respective initial values of 0, ? and 1. Semaphore empty denotes the number of available slots in the buffer, for the consumer to read from. Semaphore denotes the number of available slots in the buffer, for the producer to write to. The placeholder variables, denoted by P, Q, R, and S, in the code below can be assigned either empty or full. The valid semaphore operations are: wait ( ) and signal ( ). Producer: Consumer: do {         wait (P) ;         wait (mutex) ;         //Add item to buffer         signal (mutex) ;         signal (Q) ; } while (1) ; do {          wait (R) ;          wait (mutex) ;          //Consume item from buffer          signal (mutex) ;          signal (S) ; } while (1) ;   Which one of the following assignments to P, Q, R and S will yield the correct solution?
For the discrete-time system shown in the figure, the poles of the system transfer function are located at
Signal Processing mcq question image
Consider the following statements regarding reciprocity theorem : 1. In any passive linear bilateral network, if the single voltage source Vx, in branch x produces the current response Iy, in branch y, then the removal of the voltage source from branch x and its insertion in branch y will produce the current response iy in branch x. 2. The interchange of an ideal voltage source and an ideal ammeter in any passive, linear, bilateral circuit will not change the ammeter reading. 3. The interchange of an ideal current source and an ideal voltmeter in any passive linear bilateral circuit will change the voltmeter reading. Which of the above statements are correct ?
Consider the following statements regarding modulation : 1. The communication systems, where a weak signal is transmitted by the use of a modulation is essential in carrier signal. 2. When the frequency of the high frequency signal is varied in accordance with the intensity of the low-frequency weak signal, the modulation is said to be frequency modulation. 3. The process of recovering original baseband signal from the modulated signal is called phase modulation. Which of the above statements are correct ? 
A rectangular pulse train s(t) as shown in the figure is convolved with the signal cos2(4π × 103t). The convolved signal will be a
Signal Processing mcq question image