Bissoy.com
Doctors Medicines MCQs Q&A

Related Questions

A system provides output yi(t) when xi(t) is applied. If the system is said to be LTI then which of the following properties must satisfy? (i).If the input is x3 = ax1(t) + bx2(t), then output must be y3(t) = ay1(t) + by2(t) (ii).If the input is x(t – T), then the output must be y (t – T) (iii).If the input is x3 = ax1(t) + bx2(t), then output must be y3(t) = ay1(t) * by2(t) (iv).If the input is x(t – T), then the output must be y(t + T)
Which of the following statements is/are correct? 1. A system is said to be Finite Impulse Response (FIR), if the output samples of the system depend only on the present input and a finite number of past or previous input samples. 2. If the output of a system y(n) depends only on the present input and past inputs, but not on past outputs, then it is called a non-recursive system. 3. If the output of a system y(n) depends only on the present input and past inputs, but not on past outputs, then it is called a recursive system.
Consider a system whose input r and output y are related by the equation $$y\left( t \right) = \int\limits_{ - \infty }^\infty {x\left( {t - \tau } \right)} h\left( {2\tau } \right)d\tau $$
Signal Processing mcq question image
Where h(t) is shown in the graph
Which of the following four properties are possessed by the system? BIBO: Bounded input gives a bounded output
Causal: The system is causal.
LP : The system is low pass.
LTI: The system is linear and time-invariant.
In a receiver the input signal is 100 V, while the internal noise at the input is 10 V. With amplification the output signal is 2 V, while the output noise is 0.4 V. The noise figure of receiver is
In the question one statement is given, followed by two conclusions, I and II. You have to consider the statement to be true even if it seems to be at variance from commonly known facts. You have to decide which of the given conclusions, if any, follows from the given statement. Statement: A function is a relation between a set of input elements and a set of possible output elements where each input is related to exactly one output. Conclusion I: Every input element is related to every output element. Conclusion II: Every input element is related to one element of the output.
Below a question is given with one passage and its effects (I) and (II). One of these effects or both or none may be the effect of the statement. Read both the effect and decide which of the following answer choice correctly depicts the relationship between these cause and effect. Passage: In the urban area there exist a lot of industries, commercial places and public places religious places which involve a lot of a  people and working machinery note of sound and when this sound becomes unpleasant it is known as noise. it is one of the reasons why public authorities have divided the city into a number of zones is known as a different noise level. Effects: I        Noise leads to emotional and behavioural stress. A person may feel disturbed in the presence of loud noise such as produced by heating of drums. II       Noise may cause damage to the liver, brain, and heart.  
Which of the following are the basic differences between vibration signature and noise signature? 1. Vibration signature is essentially in the frequency range zero to 100 cps whereas noise signature is in the range 20 cps to 3000 cps. 2. Vibration signature has well-defined peaks whereas the noise signal is smeared. 3. The intensities of noise signatures arc much less than that of vibration signatures. 4. Detection of vibration signature calls for a microphone whereas that of noise can do with a pickup. Select the correct answer using the code given below.
Antenna noise temperature of a system is 210 K, noise temperature of transmission line is 123 K, loss of a transmission line connecting the antenna to receiver is 1.41 and noise temperature of the receiver cascade is 304 K. then the total system noise temperature is:
Wages of the workers are normally, the proportionality derived from their efficiency. But the concept of efficiency of labour is itself vague such as amount of physical output, output per man hour or output per man shift. But output is not the function of man alone. There are other factors which affect the output. Which among the following is/are not the factor(s) that would affect the output directly?
1. Physical condition of work
2. Nature of machinery
3. Technical process
4. Quality of raw material
5. System of management
6. Role of fellow workers
7. Competitors in the market
If input is ‘ a(l) + e ‘ where ‘e’ is the noise introduced, then what is the output if system is interpolative in nature?