Bissoy.com
Doctors Medicines MCQs Q&A

The ‘Envelope delay’ or ‘Group delay’ is the time delay that the signal component of frequency ω undergoes as it passes from the input to the output of the system.

The ‘Envelope delay’ or ‘Group delay’ is the time delay that the signal component of frequency ω undergoes as it passes from the input to the output of the system. Correct Answer True

The time delay taken to reach the output of the system from the input by a signal component is called as envelope delay or group delay.

Related Questions

Consider a system whose input r and output y are related by the equation $$y\left( t \right) = \int\limits_{ - \infty }^\infty {x\left( {t - \tau } \right)} h\left( {2\tau } \right)d\tau $$
Signal Processing mcq question image
Where h(t) is shown in the graph
Which of the following four properties are possessed by the system? BIBO: Bounded input gives a bounded output
Causal: The system is causal.
LP : The system is low pass.
LTI: The system is linear and time-invariant.
Consider the following statements regarding modulation : 1. The communication systems, where a weak signal is transmitted by the use of a modulation is essential in carrier signal. 2. When the frequency of the high frequency signal is varied in accordance with the intensity of the low-frequency weak signal, the modulation is said to be frequency modulation. 3. The process of recovering original baseband signal from the modulated signal is called phase modulation. Which of the above statements are correct ? 
Which of the following statements is/are correct? 1. A system is said to be Finite Impulse Response (FIR), if the output samples of the system depend only on the present input and a finite number of past or previous input samples. 2. If the output of a system y(n) depends only on the present input and past inputs, but not on past outputs, then it is called a non-recursive system. 3. If the output of a system y(n) depends only on the present input and past inputs, but not on past outputs, then it is called a recursive system.
A system provides output yi(t) when xi(t) is applied. If the system is said to be LTI then which of the following properties must satisfy? (i).If the input is x3 = ax1(t) + bx2(t), then output must be y3(t) = ay1(t) + by2(t) (ii).If the input is x(t – T), then the output must be y (t – T) (iii).If the input is x3 = ax1(t) + bx2(t), then output must be y3(t) = ay1(t) * by2(t) (iv).If the input is x(t – T), then the output must be y(t + T)
In an AM system receiver. the mixer translates the carrier frequency fc to a fixed intermediate frequency of 450 kHz. Given a broadcast signal of frequency 900 kHz. What is the corresponding image frequency when a superhetrodyne receiver is employed with local oscillator frequency greater than the broadcast signal frequency?
The input to a channel is a bandpass signal. It is obtained by linearly modulating a sinusoidal carrier with a single-tone signal. The output of the channel due to this input is given by
$$y\left( t \right) = \left( {{1 \over {100}}} \right)\cos \left( {100t - {{10}^{ - 6}}} \right)\cos \left( {{{10}^6}t - 1.56} \right)$$
The group delay (tg) and the phase delay (tp) in seconds, of the channel are
Which of the following statements are correct? 1. A lowpass filter passes low frequencies and stops high frequencies. 2. A highpass filter passes high frequencies and rejects low frequencies 3. A bandpass filter passes frequencies within a frequency band and attenuates frequencies outside the band. 4. A bandstop filter passes frequencies within the band and blocks/attenuates frequencies outside a frequency band.
A DSB-SC signal is generated using the carrier signal cos (ωct + θ) and modulating signal m(t). What is the envelope detector output of this DSB-SC signal?
In the question one statement is given, followed by two conclusions, I and II. You have to consider the statement to be true even if it seems to be at variance from commonly known facts. You have to decide which of the given conclusions, if any, follows from the given statement. Statement: A function is a relation between a set of input elements and a set of possible output elements where each input is related to exactly one output. Conclusion I: Every input element is related to every output element. Conclusion II: Every input element is related to one element of the output.
A signal contains components at 400 Hz and 2400 Hz This signal modulates a carrier of frequency 100 MHz. However, after demodulation, it is found that the 400 Hz signal component is present. The channel bandwidth is 15 kHz. What is the reason for the higher frequency signal not to be detected properly?