The tangent to both the curves in an ogee curve is perpendicular to each other.

The tangent to both the curves in an ogee curve is perpendicular to each other. Correct Answer False

The tangent to both the curves in an ogee curve is parallel and not perpendicular to each other. An ogee curve is a curve with two curves with one of the curve being a reverse curve to the other. Hence it is also called as a reverse curve.
Bissoy MCQ

Related Questions

Indifference curves relating to supply of labour have a number of properties some of which are mentioned below
1. Indifference curves are downward slopping
2. Indifference curves are upward slopping
3. Higher indifference curves indicate lower levels of utility
4. Higher indifference curves indicate higher levels of utility
5. Indifference curves do not intersect
6. Indifference curves intersect
7. Indifference curves are concave to the origin
8. Indifference curves are convex to the origin
Which among the following properties are not true?
Arrange the following stages in a sequence, such that they result in an ogee curve between two parallel lines AB and CD, such that they are the tangents to the arc. m) Join the adjacent ends B and C with a straight line. n) Divide the line BC into four parts using the points P1, P2, P3. o) Draw lines such that they pass through the points P1, P2, P3, and are perpendicular to the line BC. p) Draw the perpendicular lines through the points B and C such that they cut the lines passing through P1, P3 respectively at E and F. q) With the center E draw an arc BP2 and with center F draw an arc P2C, thus arc BP2C is required ogee curve.
From an alloy, two specimens are machined and tested separately under tension and compression. The engineering stress-strain curves as well as the true stress-true strain curves for tension and compression are plotted in the same diagram. Identify the correct statements:
P. The engineering stress-strain curves in tension and compression are identical.
Q. The true stress-true strain curve in compression is lower than the true stresstrue strain curve in tension due to Bauschinger effect.
R. The true stress-true strain curve in tension is above the corresponding engineering stress-strain, curve.
S. The true stress-true strain curve in tension and compression are identical.
Steps are given to draw normal and tangent to an archemedian curve. Arrange the steps, if O is the center of curve and N is point on it. i. Through N, draw a line ST perpendicular to NM. ST is the tangent to the spiral. ii. Draw a line OM equal in length to the constant of the curve and perpendicular to NO. iii. Draw the line NM which is normal to the spiral. iv. Draw a line passing through the N and O which is radius vector.
Find the value of the long curve tangent distance, if the tangent length of short and long curves were given as 23.21m and 65.87m. The total deflection is 67˚54ꞌ and the deflection angle at short curve is given as 28˚43ꞌ.
Consider the following statements about indifference curves: 1. Indifference curves are convex to the origin. 2. Higher indifference curve represents higher level of satisfaction. 3. Two indifference curves cut each other.Which of the statements given above is/are correct?
The MC curve reaches its minimum point before the AVC curve and the AC curve. In addition the MC curve intersects the AVC curve and the AC curve at their lowest point. The above statements are both true
Given are the steps to draw a tangent to given circle and parallel to given line. Arrange the steps. i. Draw a perpendicular to given line and extend to cut the circle at two points P and Q. ii. At P or Q draw perpendicular to normal then we get the tangents. iii. PQ is the normal for required tangent. iv. Draw a circle with center O and line AB as required.
Steps are given to find the normal and tangent for a cycloid. Arrange the steps if C is the centre for generating circle and PA is the directing line. N is the point on cycloid. i. Through M, draw a line MO perpendicular to the directing line PA and cutting at O. ii. With centre N and radius equal to radius of generating circle, draw an arc cutting locus of C at M. iii. Draw a perpendicular to ON at N which is tangent. iv. Draw a line joining O and N which is normal.
Which of the following statement is not true considering a cubic lattice system? are not perpendicular to each other b) Direction is parallel to plane (hkl), when uh+vk+wl=0 c) Direction is perpendicular to the plane (hkl) when u=h, v=k, w=l d) Two planes (hkl) and (abc) are perpendicular to each other if h=a, k=b, l=c