Bissoy.com
Doctors Medicines MCQs Q&A

In the “Opening a channel” phase what is the function of the “innitial window size” parameter?

In the “Opening a channel” phase what is the function of the “innitial window size” parameter? Correct Answer It specifies how many bytes of channel data can be sent

The ‘innitial window size’ specifies how many bytes of channel data can be sent.

Related Questions

The Secure Shell Connection Protocol Message exchange has the fist phase as “Opening a Channel” and it sends a message with parameters- SSH_MSG_CHANNEL_OPEN channel type sender channel innitial window size maximum packet size What is the data type sender channel/innitial window size/ channel type?
Which of the following statements is/are correct with respect to a Scott-connected transformer? I. It can do 3-phase to 2-phase conversion II. It can do 2-phase to 3-phase conversion III. It can do 2-phase to 4-phase conversion IV. It can do 3-phase to 4-phase conversion
In the “Opening a channel” phase what is the function of the “maximum packet size” parameter?
Statement (I): An alluvial channel is defined as a channel in which the flow transports sediment of the same physical characteristic as the material in the wetted surface of the channel. Statement (II): This ensures that the channel cross-section and the channel slope do not change.
In the question below are given four statements followed by four conclusions numbered I, II, III and IV. You have to take the given statements to be true even if they seem to be at variance with commonly known facts. Read all the conclusions and then decide which of the given conclusions logically follows from the given statements disregarding commonly known facts. Statements: All Stone are Hammer. No Hammer is a Bell. Some Bell are Door. All Door are Window. Conclusions: I. Some Window are Stone. II. Some Window are Bell. III. No window is a stone. IV. Some Bell are Stone.
The network formed by resistors and capacitors for modifying the rate of change of gain and the phase shift is called a compensating network. Which of the following statements are not correct ? (A) The main purpose of a compensating network is to modify the performance of op-amp ciruit over the desired frequency range (B) There are two types of op-amps : internally compensated and externally compensated (C) 741 C is an externally compensated op-amp while 709 C is internally compensated op-amp (D) The phase lag and phase lead are most commonly used compensating networks in op-amps (E) Phase lag contributes a positive phase angle and phase lead a negative phase angle Choose the most appropriate answer from the options given below : 
Consider the following C function in which size is the number of elements in the array E: int MyX(int *E, unsigned int size) {       int Y = 0;       int Z;       int i, j, k;       for(i = 0; i < size; i++) Y = Y + E[i];       for(i = 0; i < size; i++) for(j = i; j < size; j++) {       Z = 0;       for(k = i; k <= j; k++) Z = Z + E[k];       if (Z > Y) Y = Z; }       return Y; } The value returned by the function MyX is the
Consider an instance of TCP’s Additive Increase Multiplicative Decrease (AIMD) algorithm where the window size at the start of the slow start phase is 2 MSS and the threshold at the start of the first transmission is 8 MSS. Assume that a timeout occurs during the fifth transmission. Find the congestion window size at the end of the tenth transmission. 
Assume that the bandwidth for a TCP connection is 1048560 bits /sec. Let α be the value of RTT in milliseconds (rounded off to the nearest integer) after which the TCP window scale option is needed. Let β be the maximum possible window size with window scale option. Then the values of α and β are
Which of the following statements are true with regards to the selection of a sample size? (i) The sample size (n) may be a fixed percentage of lot size (N). (ii) The sample size (n) may be kept constant irrespective of lot size (N). (iii) Sample size (n) can be selected at the personal whim of the inspector.