Bissoy.com
Doctors Medicines MCQs Q&A

The instructions that pass through the fetch, decode and execution stages sequentially is known as

The instructions that pass through the fetch, decode and execution stages sequentially is known as Correct Answer linear instruction sequencing

The linear instruction sequencing is the one in which the instructions that pass through the fetch, decode and execution stages sequentially.

Related Questions

A 5-stage pipelined processor has Instruction Fetch (IF), Instruction Decode (ID), Operand Fetch (OF), Perform Operation (PO) and Write Operand (WO) stages. The IF, ID, OF and WO stages take 1 clock cycle each for any instruction. The PO stage takes 1 clock cycle for ADD and SUB instructions, 3 clock cycles for MUL instruction, and 6 clock cycles for DIV instruction respectively. Operand forwarding is used in the pipeline. What is the number of clock cycles needed to execute the following sequence of instructions? Instruction Meaning of instruction I0 : MUL R2, R0, R1 R2← R0 * R1 I1 : DIV R5, R3, R4 R5 ← R3 / R4 I2 : ADD R2, R5, R2 R2 ← R5 + R2 I3 : SUB R5, R2, R6 R5 ← R2 – R6
Which one of the following is the right syntax for DECODE? … ) b) DECODE (expression, result … , search) c) DECODE (search, result … , expression) d) DECODE (expression, search, result … )
In fetch-decode unit, the number of parallel decoders that accept the stream of fetched instructions and decode them is
The decoder unit in fetch-decode unit converts the instructions into
Consider the following code sequence having five instructions I1 to I5. Each of these instructions has the following format. OP Ri, Rj, Rk Where operation OP is performed on contents of registers Rj and Rk and the result is stored in register Ri I1: ADD R1, R2, R3 I2: MUL R7, R1, R3 I3: SUB R4, R1, R5 I4: ADD R3, R2, R4 I5: MUL R7, R8, R9 Consider the following three statements. S1: There is an anti-dependence between instructions I2 and I5 S2: There is an anti-dependence between instructions I2 and I4 S3: Within an instruction pipeline an anti-dependence always creates one or more stalls Which one of the above statements is/are correct?
In a Plane there are 37 straight lines, of which 13 pass through the point A and 11 pass through the point B. Besides, no three lines pass through one point, no lines passes through both points A and B , and no two are parallel. Find the number of points of intersection of the straight lines.
A student M scored 25% marks and gets failed in an exam because of securing 15 marks less than the pass marks. Another student N passed the exam by scoring 45% marks, which are 25 marks more than the pass marks. Later, it was found that the actual pass marks are 40% more than the initially calculated pass marks. What is the average of both the pass marks?
Consider the following statements regarding life time of any normally terminating process in an operating system. (I) The process must be in RUNNING state at least once during its execution. (II) The process must be in RUNNING state at least twice during its execution. (III) The process must be in WAITING state at least once during its execution. (IV) The process must be in READY state at least once during its execution. Which of the above statements are correct?
Study the table carefully to answer the question that follows   Schools CLASSES VI VII VIII IX X   Pass Fail Pass Fail Pass Fail Pass Fail Pass Fail A 84 12 56 12 82 9 80 14 86 12 B 56 18 64 16 88 7 64 11 73 12 C 53 16 60 10 58 12 63 9 63 18 D 62 11 62 14 64 13 61 7 53 17 E 70 15 76 17 78 10 52 13 79 1 F 58 8 72 13 72 14 45 12 75 11 What is the average number of fail students from class IX from all the schools together?
There are two students A and B. Both of them give an exam. In the exam, A scored 30% marks. If A got 14.285% marks more of the essential minimum pass marks he would pass. In the same exam, B got 45% marks and secured 28.57% marks more of the essential minimum pass marks. What are the maximum number and minimum pass marks of the exam? A. Max 600 and Min 210 B. Max 400 and Min 140 C. Max 600 and Min 200 D. Max 700 and Min 210 Which statement is/are correct?