Bissoy.com
Doctors Medicines MCQs Q&A

Which of the following routing algorithms can be used for network layer design?

Which of the following routing algorithms can be used for network layer design? Correct Answer all of the mentioned

The routing algorithm is what decides where a packet should go next. There are several routing techniques like shortest path algorithm, static and dynamic routing, decentralized routing, distance vector routing, link state routing, Hierarchical routing etc. The routing algorithms go hand in hand with the operations of all the routers in the networks. The routers are the main participants in these algorithms.

Related Questions

Consider a computer network using the distance vector routing algorithm in its network layer. The partial topology of the network is as shown below. The objective is to find the shortest-cost path from the router R to routers P and Q. Assume that R does not initially know the shortest routes to P and Q. Assume that R has three neighbouring routers denoted as X, Y, and Z. During one iteration, R measures its distance to its neighbours X, Y, and Z as 3, 2, and 5, respectively. Router R gets routing vectors from its neighbours that indicate that the distance to router P from routers X, Y, and Z are 7, 6, and 5, respectively. The routing vector also indicates that the distance to router Q from routers X, Y, and Z are 4, 6, and 8, respectively. Which of the following statement(s) is/are correct with respect to the new routing table of R, after updation during this iteration ? 
Given below are some famous algorithms and some algorithm design paradigms Algorithms Design Paradigm  1. Dijkstra's shortest path algorithms  (a) Greedy design  2. Floyd-Warshall's all-pair-shortest path algorithms  (b) Divide and conquer  3. Kruskal's minimum spanning tree algorithm  (c) Dynamic programming  4. Merge Sort algorithm     Which of the following correspondence is correct?
Some small cubes of same height 7 cm but variable length and width are put inside a large cuboid of height 21 cm. Length and width of cuboid is 32 cm and 24 cm, respectively. Small cubes are put such that cubes at the bottom most layer is of similar base area; second layer contains all the cubes of similar base area and third layer have all the cubes of similar base area. Which of the following statement(s) given below is / are TRUE? A: If side of each small cubes at bottom most layer is 8 cm, then maximum number of small cubes that can be put at bottom most layer is 12. B: If maximum of 48 cubes can be put at second layer, then side of each cube at second layer is 6 cm. C: If side of each small cubes at third layer is 1.6 cm, then maximum number of small cubes that can be put at third layer is 300.
Consider the following statements about the routing protocols. Routing Information Protocol (RIP) and Open Shortest Path First (OSPE) in an IPv4 network. I. RIP uses distance vector routing II. RIP packets are sent using UDP III. OSPF packets are sent using TCP IV. OSPF operation is based on link-state routing Which of the statements above are CORRECT?
Which of the following routing technique/techniques is/are used in distributed systems? (a) Fixed Routing (b) Virtual Routing (c) Dynamic Routing
Which statement is true regarding classless routing protocols?
1. The use of discontiguous networks is not allowed.
2. The use of variable length subnet masks is permitted.
3. RIPv1 is a classless routing protocol.
4. IGRP supports classless routing within the same autonomous system.
5. RIPv2 supports classless routing.
A network administrator views the output from the show ip route command. A network that is advertised by both RIP and IGRP appears in the routing table flagged as an IGRP route. Why is the RIP route to this network not used in the routing table?
A network administrator views the output from the show ip route command. A network that is advertised by both RIP and IGRP appears in the routing table flagged as an IGRP route. Why is the RIP route to this network not used in the routing table?
You are the administrator of a Windows 2000 Server computer. The server contains one network adapter and is a file and print server for critical company resources. You install a second network adpater in the server and connect it to the same network subnet as the first adapter. You want to ensure that the first adapter is used for all network traffic and the second adapter is used only if the first adapter fails or is disconnected from the network. You also want to ensure that the server always has network connectivity even if one network adapter fails. What should you do?
Two connected routers are configured with RIP routing. What will be the result when a router receives a routing update that contains a higher-cost path to a network already in its routing table?