Bissoy.com
Doctors Medicines MCQs Q&A

Find the gas phase mass transfer co-efficient for a unbound moisture to remove if the flux is 5 kg/sq.m sec and the difference in humidity of the liquid and the main stream is 0.5 units.

Find the gas phase mass transfer co-efficient for a unbound moisture to remove if the flux is 5 kg/sq.m sec and the difference in humidity of the liquid and the main stream is 0.5 units. Correct Answer 10

Flux= Mass transfer co-efficient * (Ys-Y) Mass transfer co-efficient= 5/0.5 = 10.

Related Questions

A stream of air at 100 kPa pressure and 300 K is flowing on the top surface of a thin flat sheet of solid naphthalene of length 0.2 m with a velocity of 20 m/sec. The other data are: Mass diffusivity of naphthalene vapor in air = 6 * 10 –6 m2/sec Kinematic viscosity of air = 1.5 * 10 –5 m2.sc Concentration of naphthalene at the air-solid naphthalene interface = 1 * 10 – 5 kmol/m3 Calculate the overage mass transfer coefficient over the flat plate. Note: For heat transfer over a flat plate, convective heat transfer coefficient for laminar flow can be calculated by the equation. Nu = 0.664 ReL1/2 Pr1/3 you may use analogy between mass and heat transfer.
Experiments were conducted to determine the flux of a species A in a stagnant medium across a gas-liquid interface. The overall mass transfer co-efficient based on the liquid side for dilute systems for the above was estimated to be 4 × 10-3 kg mole/m2.s. The equilibrium data for the system is given as y = 2x. The flux across the interface (in kg mole/m2.s) for bulk concentrations of A in gas phase and liquid phase as y = 0.4 and x = 0.01 respectively is
The fresh feed to an ammonia synthesis reactor contains nitrogen, hydrogen and 2.0 mole per cent inerts. The molar ratio of H2:N2 is 3:1. The product stream consists of pure ammonia. Since conversion in the reactor is only 15%, a recycle stream is used and in order to avoid build-up of inerts, a purge stream is withdrawn. The rate of purge stream is adjusted to keep inert concentration in the recycle stream at 8 mole per cent. For a fresh feed rate of 100 moles/hr. Note that recycle stream contains only nitrogen, hydrogen and inerts. The N2:H2 ratio of 1:3 is maintained in every process stream, and calculate the moles of nitrogen entering the reactor and in the recycle stream?
The fresh feed to an ammonia synthesis reactor contains nitrogen, hydrogen and 2.0 mole per cent inerts. The molar ratio of H2:N2 is 3:1. The product stream consists of pure ammonia. Since conversion in the reactor is only 15%, a recycle stream is used and in order to avoid build-up of inerts, a purge stream is withdrawn. The rate of purge stream is adjusted to keep inert concentration in the recycle stream at 8 mole per cent. For a fresh feed rate of 100 moles/hr. Note that recycle stream contains only nitrogen, hydrogen and inerts. The N2:H2 ratio of 1:3 is maintained in every process stream, and calculate the number of moles, moles of inerts and moles of hydrogen in the recycle stream?
An operating system uses the Banker’s algorithm for deadlock avoidance when managing the allocation of three resource types X, Y, and Z to three processes P0, P1, and P2. The table given below presents the current system state. Here, the Allocation matrix shows the current number of resources of each type allocated to each process and the Max matrix shows the maximum number of resources of each type required by each process during its execution.   Allocation Max   X Y Z X Y Z P0 0 0 1 8 4 3 P1 3 2 0 6 2 0 P2 2 1 1 3 3 3   There are 3 units of type X, 2 units of type Y and 2 units of type Z still available. The system is currently in a safe state. Consider the following independent requests for additional resources in the current state: REQ1: P0 requests 0 units of X, 0 units of Y and 2 units of Z REQ2: P1 requests 2 units of X, 0 units of Y and 0 units of Z Which one of the following is TRUE?
In the question below are given six statements followed by four conclusions numbered I, II, III and IV. You have to take the given statements to be true even if they seem to be at variance with commonly known facts. Read all the conclusions and then decide which of the given conclusions logically follows from the given statements disregarding commonly known facts. Statements: All Petrol are Gasoline. No petrol is Water. Some Water are Gas. Some Moisture are Gas. All Gasoline are Fire No Moisture is Fire Conclusions: I. Some Moisture are Gasoline. II. Some Water are Moisture. III. Some Gasoline are Gas. IV. Some Petrol are Moisture.
The rate of electricity in the rural area is given below: i) up to 25 units - Rs 5 per unit ii) up to 75 units - Rs 7 per units iii) up to 100 units - Rs 9 per units iv) After 100 units - Rs 13 per units Additional charge after 100 units = Rs. 50 The consumption of the electricity of the household is 120 units. How much electricity bill he has to pay?
The fresh feed to an ammonia synthesis reactor contains nitrogen, hydrogen and 2.0 mole per cent inerts. The molar ratio of H2:N2 is 3:1. The product stream consists of pure ammonia. Since conversion in the reactor is only 15%, a recycle stream is used and in order to avoid build-up of inerts, a purge stream is withdrawn. The rate of purge stream is adjusted to keep inert concentration in the recycle stream at 8 mole per cent. For a fresh feed rate of 100 moles/hr. Note that recycle stream contains only nitrogen, hydrogen and inerts. The N2:H2 ratio of 1:3 is maintained in every process stream. Calculate the moles of ammonia produced.
In a wetted-wall tower, an air-H2S mixture is flowing by a film of water which is flowing as a thin film down a vertical plate. The H2S is being absorbed from the air to the water at a total pressure of 1.50 atm abs and 30oC. The value of kc of 9.567×10-4 m/s has been predicted for the gas-phase mass-transfer coefficient. At a given point the mole fraction of H2S in the liquid at the liquid-gas interface is 2.0×10-5 and pA of H2S in the gas is 0.05 atm. The Henry’s law equilibrium relation is pA(atm) = 609xA (mole fraction in liquid). Calculate the rate of absorption of H2S.
Raw material purchased:
1st January, 600 units @ Rs. 12 per unit
12th January, 500 units @ Rs. 14 per unit
21st January, 300 units @ Rs. 13 per unit
Raw material issued for manufacture:
3rd January 300 units
5th January 124 units
15th January 250 units
16th January 300 units
Raw material returned to stores from manufacturing department on 14th January, 50 units. The material is issued on First-in-First out method.
The value of material remaining in store on 21st January will be: