Bissoy.com
Doctors Medicines MCQs Q&A

During fire emergency in high rise building which escape way should be used?

During fire emergency in high rise building which escape way should be used? Correct Answer Emergency exit

Explanation:

  • Fire safety in high-rise buildings is very crucial. Fire claims huge loss of lives and property in the High Rise Buildings each year.
  • Though high-rise buildings have been designed and built with safety in mind. The walls, the doors between flats, stairs, and corridors are specially designed to resist fire, check smoke to some extent. As per National Building Code, high-rise buildings should have Smoke Detectors, Sprinklers, First Aid Fire Fighting system, PA system, Adequate water supply, Fire pumps, Fire escape routes, Fireman Lift, Service shaft enclosures, compact mentation, approved electrical system, refuse area, etc. Outside the high-rise buildings, adequate access roads and surrounding areas are so designed so as the emergency vehicles can get as near as possible.
  • In most cases, the fire escape procedure is the same as for a single-family dwelling: “Get Out and Stay Out”. Sometimes, however, it’s safe to stay in the building, separating yourself from the effects of a fire and wait to be rescued.
  • During fire emergencies in high-rise buildings, an Emergency exit should be used.

Related Questions

Six buildings L. M, N, X, Y and Z are in a circle facing the centre. Each building is exactly opposite another one. Building X is not immediately next to either Building M or Building Z. Building M is to Building Y's immediate right/ Building N is exactly opposite Building M. Building L, which is opposite Building X, has Building Z to its immediate right. Which of the following buildings is located to Building Z's immediate right?
Six buildings ‘L’, ‘M’, ‘N’, ‘Y’ and ‘Z’ stand in a circle facing the centre. Each building is exactly opposite another one. Building ‘X’ is NOT immediately next to either building ‘M’ or ‘Z’. Building ‘M’ is to building Y’s immediate right. Building ‘N’ is exactly opposite building ‘M’. Building ‘L’, which is opposite building ‘X’, has building ‘Z’ to its immediate right. Which of the following buildings is located between building ‘L’ and ‘Y’?  
Six buildings L, M, N, X, Y, and Z stand in a circle facing the centre. Each building is exactly opposite another one. Building X is not immediately next to either building M or Z. Building M is to building Y’s immediate right. Building N is exactly opposite building M. Building L which is opposite building X, has building Z to its immediate right. Which of the following buildings is located to building Z’s immediate right?
Six buildings L, M, N, X, Y and Z stand in a circle facing the centre. Each building is exactly opposite another one. Building X is not immediately next to either building M or Z. Building M is to building Y’s immediate right. Building N is exactly opposite building M. Building L, which is opposite building X, has building Z to its immediate right. Which of the following buildings is located to building X’s immediate right?
“In case of failure of constitutional machinery in a state, then the center takes over the state government under article 356 as mentioned in the constitution” Which of the following emergency is explained above? National emergency State emergency Financial emergency Constitutional emergency
A cam should be designed only using uniform rise and fall within half of the cam, the remaining is dwell period, and without any dwell period in between the rise -fall periods and rise and fall periods should be same. The maximum rise in follower is 30 mm. How much the follower will rise when the follower is 120 degrees from its initial position of a cam?
A cam should be designed only using uniform rise and fall within half of the cam, the remaining is dwell period, and without any dwell period in between the rise-fall periods and rise and fall periods should be same. The maximum rise in follower is 45 mm. How much the follower will rise when the follower is 45 degrees from its initial position of a cam?
A cam should be designed only using uniform rise and fall within the second half of cam profile, the first half is dwell period, without any dwell period in between the rise and fall periods and rise and fall periods should be same. The maximum rise in follower is 45 mm. How much the follower will rise when the follower is 120 degrees from its initial position of a cam?
A cam should be designed only using uniform rise and fall within the second half of cam profile, the first half is dwell period, without any dwell period in between the rise and fall periods and rise and fall periods should be same. The maximum rise in follower is 55 mm. How much the follower will rise when the follower is 240 degrees from its initial position of a cam?
A cam should be designed only using uniform rise and fall within first half of cam profile, the remaining is dwell period, and without any dwell period in between the rise-fall periods and rise and fall periods should be same. The maximum rise in follower is 35 mm. How much the follower will rise when the follower is 240 degrees from its initial position of a cam?