Consider the following reasons for using non-conventional machining processes: 1. High-strength alloys 2. Complex surfaces 3. High accuracies and surfaces finish Which of the above are correct?

1 and 2 only
1 and 3 only
2 and 3 only
1, 2 and 3

LohaHridoy

4 views

2025-01-04 04:42

1 Answers

AhmedNazir

Option 4 : 1, 2 and 3

Benefits of Unconventional Machining

New materials having high strength and hardness (NImonic alloys, Tungsten, Moleyebdenum and columbium alloys) can be easily machined.
Complex shapes can be easily machined.
High accuracies and surface finish.

4 views Answered 2022-09-04 04:29

Related Questions

Consider the following statements: Machine tool beds are made using grey cast iron due to 1. high tensile strength and ductility 2. high compressive strength and damping property 3. castability and low cost of production 4. machinability and low material cost Which of the above statements are correct?

1 Answers 5 Views

In an alternator, the armature winding is kept stationary while the field winding is kept rotating for the following reasons: 1. Armature handles very large current and high voltage 2. Armature fabrication, involving deep slots to accommodate large coils, is easy if armature is kept stationary 3. It is easier to cool the stator than the rotor Which of the above reasons are correct?

1 Answers 5 Views

Consider the following statements regarding a turbine: 1. Specific speed plays an important role in the selection of the type of turbine. 2. An increase in specific speed of the turbine is accompanied by higher maximum efficiency. 3. The runner of too high specific speed with high available head increases the cost of the turbine on account of the high mechanical strength required. Which of the above statements are correct?

1 Answers 5 Views

In the question given below, four sentences are given which may or may not be grammatically correct. From the given options, choose the grammatically correct sentence. A. Literature often portrayed children as one-dimensional, but children are as complex as adults. B. Literature often portrays children as one-dimensional, but children are as complex as adults. C. Literature often portrays children as one-dimensional, but children are so complex as adults. D. Literature often portrays children as one-dimensional, but children are more complex as adults. ?

1 Answers 4 Views

The influence of shape of aggregate in strength and workability of concrete are given below in statements S1, S2, S3 and S4. Which of the statements are correct S1: Rounded aggregate produces concrete with high workability and low strength. S2: Angular aggregate produces concrete with high workability and low strength. S3: Rounded aggregate produces concrete with low workability and high strength. S4: Angular aggregate produces concrete with low workability and high strength.?

1 Answers 5 Views

Consider the following properties regarding insulation for cables: 1. A low specific resistance 2. High temperature withstand 3. High dielectric strength Which of the above properties of insulation are correct while using cables?

1 Answers 4 Views

In the case of the design of friction clutches, the uniform rate of wear theory is used over uniform pressure. The reasons may be the following: 1. It gives lower frictional torque. 2. It gives higher frictional torque. 3. The intensity of pressure is maximum at the inner radius and minimum at the outer radius of the friction or contact surfaces. 4. This concept is prevalent for running and old clutches. Which of the above reasons is correct?

1 Answers 4 Views

Consider the following: The parallel fillet welded joint is designed for 1) tensile strength 2) compressive strength 3) bending strength 4) shear strength Which of the above is/are correct?

1 Answers 7 Views

Which of the following statements regarding laws governing the friction between dry surfaces are correct 1. The friction force is dependent on the velocity of sliding. 2. The friction force is directly proportional to the normal force. 3. The friction force is dependent on the materials of the contact surfaces. 4. The Friction force is independent of the area of contact surfaces.?

1 Answers 4 Views

Consider the following given statements about auto-transformers and choose the one which is/are correct. 1. Auto-transformers require less copper as compared to a conventional,2 winding transformer of the same capacity. 2. Auto-transformers provide isolation between the primary and secondary windings. 3. Auto- transformer has less leakage reactance as compared to the conventional, 2 winding transformer of the same capacity.?

1 Answers 5 Views

এক্সাম দিয়ে মেধা যাচাই করুন

Job Preparation (1125)

Admission (754)

এসএসসি (10)

এইচএসসি (5)