Consider the following statements: In the case of involute gears in contact 1. the motion is one of pure rolling 2. pressure angle does not change during contact 3. velocity ratio does not change 4. output torque of the driven gear changes Which of the above statements are correct?

1 and 2
2 and 4
2 and 3
3 and 4

LohaHridoy

4 views

2025-01-04 04:42

1 Answers

AhmedNazir

Option 3 : 2 and 3

In the case of involute gears in contact

The motion is partially sliding and partially rolling.
Pressure angle remains contact during contact.
Velocity ratio does not change.
Output torque remains same for pinion and gear.

4 views Answered 2022-09-04 04:29

Related Questions

Which of the following statements are correct for mating gears with involute profiles 1. The pressure angle, from the start of the engagement to the end of the engagement, remains constant. 2. The pressure angle is maximum at the beginning of the engagement, reduces to zero at pitch point, starts decreasing and again becomes maximum at the end of the engagement. 3. The face and flank of the teeth are generated by a single curve and the normal to this curve at any point is tangent to the base circle of the gear. 4. The centre distance for a pair of mating gears can be varied within limits without altering the velocity ratio. Select the correct answer using the code given below.?

1 Answers 4 Views

Consider the following statements: 1. In an Impulse turbine, the pressure of the flowing water remains un- changed and is equal to atmospheric Pressure. 2. In Impulse turbines, the water impinges on the buckets with ‘Pressure energy’. 3. In a Reaction turbine, the pressure of the flowing water remains un- changed and is equal to atmospheric pressure. Which of the above statements is/are correct?

1 Answers 4 Views

In the case of the design of friction clutches, the uniform rate of wear theory is used over uniform pressure. The reasons may be the following: 1. It gives lower frictional torque. 2. It gives higher frictional torque. 3. The intensity of pressure is maximum at the inner radius and minimum at the outer radius of the friction or contact surfaces. 4. This concept is prevalent for running and old clutches. Which of the above reasons is correct?

1 Answers 4 Views

Consider the following statements regarding gear tooth designing for gear drive: 1. Tooth profiles not designed as per ‘law of gearing’ will cause vibration and impact problems even at low speed. 2. As the gears go through their mesh, the pitch point must remain stationary on the line of centres. 3. In a correctly designed tooth profile, the line of action of successive instantaneous points of contact will pass through the stationary pitch point. Which of the above statements are correct?

1 Answers 7 Views

Statement (I): Two non-intersecting and non-parallel, i.e., non-coplanar, shafts connected by gears are called skew-bevel gears or spiral gears, and this type of gearing has a line contact the rotation of which about the axes generates the two hyperboloid pitch surfaces. Statement (II): A hyperboloid is a 3D surface formed by revolving a straight line about an axis (not in the same plane), such that every point on the line remains at a constant distance from the axis.?

1 Answers 5 Views

Statement (I): The epicyclic gear train has a central gear and an epicyclic gear which produces epicyclic motion being moved by a crank arm. Statement (II): The arm contains the bearings for the epicyclic gear to maintain two gears in mesh. ?

1 Answers 4 Views

Consider the following statements: In case of helical gears, teeth are cut at an angle to the axis of rotation of the gears. 1) Helix angle introduces another ratio called axial contact ratio. 2) Transverse contact ratio is equal to axial contact ratio in helical gears. 3) Large transverse contact ratio does not allow multiple teeth to share the load. 4) Large axial contact ratio will cause larger axial force component Which of the above statements are correct?

1 Answers 5 Views

Consider the following statements: The axis of spiral bevel gear are non-parallel and intersecting. 1) The most common pressure angle for spiral bevel gear is 20° 2) The most common spiral angle for spiral bevel gear is 35. 3) Spirals bevel gears are generally interchangeable. 4) Spirals are noisy and recommended for low speeds of 10 m /s. Which of the above statements are correct?

1 Answers 4 Views

The interference between a given pinion tooth and a gear tooth can be avoided by using 1. smaller pressure angle 2. larger pressure angle 3. Less number of teeth on the gear for a pinion with predefined number of teeth 4. More number of teeth on the gear for a pinion with predefined number of teeth Which of the above statements are correct?

1 Answers 7 Views

Which of the following statements are correct in reference to rule of procedure for 'Motion For Adjournment on a matter of Public importance' in Rajasthan Legislative Assembly A) Speaker's consent necessary to make motion. B) The motion shall raise a question of privilege. C) The motion shall be restricted to specific matter of recent occurence. D) Not more than one such motion shall be made at the same sitting. Select the correct answer using code given below.?

1 Answers 7 Views

এক্সাম দিয়ে মেধা যাচাই করুন

Job Preparation (1125)

Admission (754)

এসএসসি (10)

এইচএসসি (5)