When a tank containing liquid moves with an acceleration in the horizontal direction, then the free surface of the liquid?

Remains horizontal
Becomes curved
Falls on the front end
Falls on the back end

LohaHridoy

5 views

2025-01-04 04:42

1 Answers

AhmedNazir

Answer: Option 3

Let'

5 views Answered 2022-09-01 13:21

Related Questions

An empty fuel tank of a car was filled with A type petrol. When the tank was half-empty, it was filled with B type petrol. Again when the tank was half-empty, it was filled with A type petrol. When the tank was half-empty again, it was filled with B type petrol. What is the percentage of A type petrol at present in the tank?

1 Answers 5 Views

An empty fuel tank of a car was filled with A type petrol. When the tank was half-empty, it was filled with B type petrol. Again when the tank was half-empty, it was filled with A type petrol. When the tank was half-empty again, it was filled with B type petrol. What is the percentage of A type petrol at present in the tank ?

1 Answers 7 Views

In the below figure, PC is the connecting rod and OC is the crank making an angle $$\theta $$ with the line of stroke PO and rotates with uniform angular velocity at $$\omega $$ rad/s. The Klien's acceleration diagram for determining the acceleration of the piston P is shown by quadrilateral CQNO, the acceleration of the piston is _________ when the crank OC and connecting rod PC are at right angles to each other.?

1 Answers 5 Views

A semicircular disc rests on a horizontal surface with its top flat surface horizontal and circular portion touching down. The coefficient of friction between semi circular disc and horizontal surface is µ. This disc is to be pulled by a horizontal force applied at one edge and it always remains horizontal. When the disc is about to start moving, its top horizontal force will?

1 Answers 11 Views

In the below figure, PC is the connecting rod and OC is the crank making an angle θ with the line of stroke PO and rotates with uniform angular velocity at $$\omega $$ rad/s. The Klien's acceleration diagram for determining the acceleration of the piston P is shown by quadrilateral CQNO. The acceleration of the piston P with respect to the crank-pin C is given by?

1 Answers 4 Views

Height of liquid in agitation tank is normally maintained equal to the tank diameter. However, if the tank is too tall and a large liquid hold up is desired, then two or more impellers mounted on the same shaft may be used. The clearance between the tank bottom and the bottom most impeller should be about (where, D = impeller diameter)?

1 Answers 6 Views

The total pressure on a horizontally immersed surface is (where w = Specific weight of the liquid, A = Area of the immersed surface, and x = Depth of the centre of gravity of the immersed surface from the liquid surface)?

1 Answers 5 Views

The depth of centre of pressure (h) for a vertically immersed surface from the liquid surface is given by (where IG = Moment of inertia of the immersed surface about horizontal axis through its centre of gravity, A = Area of immersed surface, and x = Depth of centre of gravity of the immersed surface from the liquid surface)?

1 Answers 4 Views

A tank filled partially with a liquid is subjected to a uniform horizontal acceleration. Which of the following is true for the surface of liquid in the tank?

1 Answers 5 Views

A closed tank containing water is moving in a horizontal direction along a straight line at a constant speed. The tank also contains a steel ball and a bubble of air. If the tank is decelerated horizontally, theni) the ball will move to the frontii) the bubble will move to the frontiii) the ball will move to the reariv) the bubble will move to the rear Find out which of the above statements are correct ?

1 Answers 11 Views

এক্সাম দিয়ে মেধা যাচাই করুন

Job Preparation (1125)

Admission (754)

এসএসসি (10)

এইচএসসি (5)